Filter
Top Products
4
ITEM ASCII HEX VALUE
MENU POSITION MP 4Dh 50h 0 (Upper left), 1 (Lower right)
EXPAND MODE EX 45h 58h 1 - 4
FRAME POSITION FM 46h 4Dh 1 - 5
AUDIO MODE AU 41h 55h 1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO)
VIDEO SIGNAL VS 56h 53h 0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
ANAMORPHIC SC 53h 43h 0 (OFF), 1 (ON)
LANGUAGE LG 4Ch 47h 0 (
), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 ( )
RESET ALL
RSTALL
52h 53h 54h 41h 4Ch 4Ch
MEMORY CALL MMC 4Dh 4Dh 43h 0 (AUTO), 1 (USER1), 2 (USER2)
HORIZ. POSITION HP 48h 50h + (increase), – (decrease)
VERT. POSITION VP 56h 50h + (increase), – (decrease)
FINE SYNC. FN 46h 4Eh 00 - 39
TRACKING TRK 54h 52h 4Bh + (increase), – (decrease)
COMPUTER INPUT CIN 67h 49h 4Eh 0 (RGB), 1 (YCBCR/YPBPR)
HOLD HLD 48h 4Ch 44h 0 (AUTO), 1 (ON), 2 (OFF)
HOLD BEGIN HLB 48h 4Ch 42h –01 - –99
HOLD END HLE 48h 4Ch 45h 01 - 99
CLAMP POSITION CLP 43h 4Ch 50h 00 - 63
CLAMP WIDTH CLW 43h 4Ch 57h 01 - 63
HORIZ. PIXELS HPL 48h 50h 4Ch 0000 - 9999
VERT LINES VLN 56h 4Ch 4Eh 0000 - 9999
PLL PLL 50h 4Ch 4Ch 0 (AUTO), 1 (0), 2 (1), 3 (2), 4 (3), 5 (4), 6 (5), 7 (6), 8 (7)
VERT.SYNC VSC 56h 53h 43h 0 (AUTO), 1 (ON), 2 (OFF)
SHUTTER (U) SHU 53h 48h 55h 000 - 383
SHUTTER (L) SHL 53h 48h 4Ch 000 - 383
SHUTTER (LS) SHLS 53h 48h 4Ch 53h 000 - 510
SHUTTER (RS) SHRS 53h 48h 52h 53h 000 - 510
MUTE MUTE 4Dh 55h 54h 45h 0 (MUTE OFF), 1 (MUTE ON)
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example 1] Set the AUTO POWER ON to ON.
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' (Command echo back)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 41 50 4F 4E 30 0D Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' ' ' AUTO POWER ON to ON
30 30 41 50 4F 4E 30 0D Command received
'0' '0' 'A' 'P' 'O' 'N' '1' ' ' (Command echo back)
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and
the difference data of B from G.
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 53 0D Command to confirm
'0' '0' 'S' ' ' setting of TINT
30 30 53 2B 31 30 0D Command (setting of TINT
'0' '0' 'S' '+' '1' '0' ' ' is +10) carried out