Filter
Top Products
EN – 5
ENGLISH
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It may cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in User Manual, do
not attempt to service this product by yourself.
Please contact your dealer when you want to fix,
adjust, or inspect the projector.
Do not modify the projector.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is dam-
aged, unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projector on a level and stable surface only.
Do not look into the lens when the projector is
operating.
It may hurt your eyes. Never let children look into
the lens when the projector is on.
Do not unplug the power cord during
operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. Wait for the fan to stop before unplug-
ging the power cord.
Do not touch the air outlet grilles and bottom
plate.
Do not touch them or put other equipment close to
the air outlet grilles because they become hot during
operation. The heated air outlet grilles and bottom
plate may cause injury or damage to other equip-
ment. Also, do not put the projector on a desk that is
easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventila-
tion slots become clogged with dirt or dust, the
temperature inside of the projector may rise and
cause some troubles, such as damage of inside parts,
and shortening the life of the panels.
Do not look into the air outlet grilles when
projector is operating.
Heat, dust, etc. may blow out of them and hurt your
eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector
quality and fire.
Place of installation
For safety’s sake, do not use the projector at any
place subjected to high temperature and high hu-
midity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C)
and +95°F (+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the
projector to prevent the projector from being
overheated.
• Do not install the projector at a place that is
unstable or subject to vibration.
• Do not install the projector near any equipment
that produces a strong magnetic field. Also re-
frain from installing the projector near any cable
carrying a large amount of current.
• Place the projector on a solid, vibration-free
surface. Otherwise it may fall, causing serious
injury or damage.
• Do not stand the projector on its end. It may fall,
causing serious injury or damage.
• Slanting the projector more than ±10˚(right and
left) or ±30˚(front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning
unit or heater to avoid the air outlet and inlet
grilles from being exposed to hot air.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.