Filter
Top Products
Motion MCW with MediaWave Computer – Installation and Assembly Procedure
ii Document No. 002-15-0010
Motion Proprietary & Confidential
Copyright © 2009 Motion Computing, Inc. as an unpublished work
Table of Contents
REVISION HISTORY ................................................................................................................................................ I
TABLE OF CONTENTS ...........................................................................................................................................II
1. BASE WITH POWER SUPPLY SHROUD INSTALLED ............................................................................. 1
1.1 REMOVE THE PLASTIC SHROUD THAT COVERS THE POWER SUPPLY .................................................................. 1
2. COLUMN ASSEMBLY ..................................................................................................................................... 1
2.1 LAY BASE ON ITS BACK .................................................................................................................................... 2
2.2 POSITION COLUMN ABOVE BASE ....................................................................................................................... 2
2.3 INSERT BOLTS THROUGH THE BOTTOM OF THE CART INTO THE COLUMN. THREAD EACH BOLT BEFORE FULLY
TIGHTENING ANY BOLT. TIGHTEN ALL FOUR BOLTS. ........................................................................................ 3
2.4 SET CART UPRIGHT ........................................................................................................................................... 3
2.5 REMOVE ONE SCREW AND LOOSEN THE OTHER SCREW OF THE COLUMN TOP PLATE ......................................... 4
2.6 INSERT DECORATIVE COVER IN THE BACK OF THE COLUMN CHANNEL GROVES. ............................................... 4
2.7 SLIDE DECORATIVE COVER DOWN TO WITHIN 24 INCHES OF THE BASE ............................................................. 4
2.8 ROUTE CABLES BEHIND THE DECORATIVE COVER ............................................................................................ 5
2.9 SLIDE DECORATIVE COVER TO THE BOTTOM OF THE COLUMN .......................................................................... 5
2.10 HOLDING CABLE IN THE CHANNEL AND INSERT SECOND DECORATIVE COVER IN THE BACK COLUMN CHANNEL
GROVES ............................................................................................................................................................ 5
2.11 SLIDE THE DECORATIVE COVER DOWN SO IT TOUCHES THE FIRST COVER ......................................................... 6
3. INSTALLING THE WORK SURFACE AND DRAWER ............................................................................. 6
3.1 REMOVE THE DRAWERS BY PRESSING THE PLASTIC RELEASE TABS ON THE INSIDE OF THE DRAWER GLIDE
RAILS................................................................................................................................................................ 6
3.2 NOTE WHERE THE ALLEN SET SCREWS ARE LOCATED ...................................................................................... 7
3.3 SLIDE THE WORK SURFACE DRAWER ASSEMBLY MOUNTING BRACKET INTO THE ADJUSTABLE RAIL LOCATED
ON THE FRONT COLUMN ................................................................................................................................... 7
3.4 SLIDE THE WORK SURFACE DRAWER ASSEMBLY DOWN THE RAIL TO ABOUT 2 INCHES (4.4 CM) FROM THE
BOTTOM OF THE RAIL. ...................................................................................................................................... 7
3.5 TIGHTEN THE SET SCREWS................................................................................................................................ 8
3.6 FULLY TIGHTEN THE SET SCREWS ..................................................................................................................... 8
3.7 REINSTALL THE DRAWER BY SLIDING IT ONTO THE DRAWER RAILS .................................................................. 9
4. ASSEMBLE THE CPU/MONITOR VESA MOUNT ASSEMBLY ............................................................ 10
4.1 ATTACH METAL SPACERS TO THE FRONT CPU VESA MOUNT PLATE CORNERS ............................................. 10
4.2 PLACE NYLON SPACERS OVER THE MONITOR VESA MOUNT PLATE THREADED INSERTS WHERE ARROWS
INDICATE ........................................................................................................................................................ 10
4.3 INSERT SCREWS THROUGH THE FRONT CPU VESA MOUNT PLATE HOLE AND THROUGH THE NYLON SPACERS,
THREADING THEM INTO THE MONITOR VESA MOUNT PLATE THREADED INSERTS ........................................ 11
4.4 ATTACH THE FLUSH TILTING VESA MOUNT BRACKET TO THE BACK CPU VESA MOUNT PLATE ................ 11
4.5 PLACE THE MEDIA WAVE COMPUTER ONTO THE FRONT CPU VESA MOUNT PLATE, EVENLY SPACED
BETWEEN THE METAL SPACERS AND CONNECTORS FACING DOWN ................................................................. 11
4.6 ATTACH THE BACK CPU VESA MOUNT PLATE TO THE FRONT CPU VESA MOUNT PLATE, USING THE
THREADED METAL SPACERS ATTACHED TO THE FRONT PLATE........................................................................ 12
5. INSTALL THE MONITOR/CPU MOUNT ASSEMBLY BY SLIDING THE FLUSH TILTING VESA
MOUNT BRACKET INTO THE FRONT OF THE COLUMN RAIL ...................................................... 12
5.1 POSITION THE VESA MOUNT BRACKET ABOUT ONE INCH FROM THE TOP OF THE COLUMN RAIL AND SECURE
BY TIGHTENING THE SET SCREWS ................................................................................................................... 13
6. ASSEMBLE THE BATTERY GAUGE HOUSING ..................................................................................... 13