Filter
Top Products
WD-8198B page 2 of 2
How to Order
To determine the kit that wil suit your application, refer to the Kit
Combinations on the reverse side. When you have decided on a kit,
the model number and voltage must be specified when ordering.
Example: WD100, 12 Volt
Approximate Shipping Weights and Dimensions for each kit are
specified on the reverse side of this bulletin, under Kit Combinations.
Order oil line assembly separately.
Warranty
A limited warranty on materials and workmanship is given with this FW
Murphy product. A copy of the warranty may be viewed or printed by going to
www.fwmurphy.com/support/warranty.htm
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
P.S.I.
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
F
8
-7/16 in.
(
214 mm)
5-7/8 in.
(149 mm)
Mounting
holes 2
places
9/32
(7 mm)
diameter
2-13/16 in.
(71 mm)
3-9/32 in.
(83 mm)
2-3/4 in.
(70 mm)
3-7/16 in.
(87 mm)
Fuel-In
Fuel Return Line
CKV2336
Injector
Injection
Pump
SV
valve
PRV50
Glass
Filter
DIESEL ENGINE
Fuel Tank
GNCSW
1
SW
2
B
518PH
Fuse
20P
100 psi
20T
250 F
Battery
WD PANEL
Fuel
Pump
Typical Wiring to Diesel Engine
Special Notes:
• Murphy Pressure Relief Valve; model PRV50 is factory set to start open-
ing at 25 psi (172 kPa) [1.72 bar]. This is done to protect the fuel filter
canister from bursting due to high pressure.
• Install the Murphy Check Relief Valve, model CKV2336, as close as
possible to the injection pump. When the CKV2336 is installed
properly it should prevent the injection pump from siphoning fuel thus
not allowing continued operation after the SV valve closes.
• Install the SV-Series fuel valve as close as possible to the injection
pump inlet port.
• All fittings must be air tight.
On some fuel
systems it may
be necessary to
install check
valve here.
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
P.S.I.
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
F
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
P.S.I.
M
U
R
P
M
U
R
H
Y
S
W
I
C
H
G
A
G
E
®
F
Mounting
Surface
WD Panel
Rotating/Tilting Panel
It is the ability of this panel to mount in many
different positions (Swichgage instruments can be
rotated, the panel tilted) that allows for instrument
visibility without a difficult installation or interference
with other engine equipment.
Dimensions
CAUTION
::
Certain dangers
to human safety and to
equipment may occur if
some equipment is stopped without
pre-warning. In these cases, it is
recommended that monitored
functions be limited to alarm-only
or to alarm before shutdown.
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
Printed in U.S.A. 12 0 140
In order to consistently bring you the highest quality, full featured products, we reserve the right to change
our specifications and designs at any time. MURPHY, the Murphy logo, and Swichgage
®
are registered and/or
common law trademarks of Murphy Industries, Inc. This document, including textual matter and illustrations,
is copyright protected by Murphy Industries, Inc., with all rights reserved. (c) 2006 Murphy Industries, Inc.
www.fwmurphy.com
918.317.4100 Email: sales@fwmurphy.com