Filter
Top Products
Introduction
The NETGEAR
®
5/8-Port Fast Ethernet Switch Model FS105 v2/FS108 v2 provides you with
a low-cost, reliable, high-performance switch to connect up to five or eight different Ethernet-
enabled devices (such as computers, file servers, print servers, printers, routers and hubs).
You use the FS105 v2/FS108 v2 switch to build a small network that enables you to have 10
Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add
extra computers to your cable or DSL router. Unlike a hub that shares its connection with all
devices, the FS105 v2/FS108 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps)
connection between two devices. If a device has full-duplex capability, the FS105 v2/FS108 v2
switch provides a 200 Mbps (or 20 Mbps) connection.
Ethernet cables come as either straight-through or crossover cables—depending on whether
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one
you use. Each port on the FS105 v2/FS108 v2 switch automatically configures itself correctly
when you plug in a device’s cable.
If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7
days a week on the Web (www.NETGEAR.com), by e-mail (support@NETGEAR.com) and by
phone (see the provided support information card for phone numbers).
Installation Overview
Estimated Time: 5–10 minutes
1. Unpack the box and verify the contents.
2. Prepare to install the switch.
3. Install the switch and connect the other devices.
Fast Ethernet Switch FS105 v2/FS108 v2
M
O
D
E
L
F
S
105
Fa
s
t Ethe
rn
et S
w
itch
M
O
D
E
L
F
S
10
8
F
a
s
t
E
t
h
e
r
n
e
t
S
w
i
t
c
h
P
W
R
1
3
4
5
76
F
A
S
T
E
T
H
E
R
N
E
T
S
W
I
T
C
H
FS108
O
n
=
L
i
n
k
B
l
i
n
k
=
A
c
t
2
8
1
0
0
M
1
0
M
A
u
to
1
0
/1
0
0
M
b
p
s
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch has been suppressed in
accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain
restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch is shielded against the
generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) does not exceed the Class B
limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) respecte les limites de bruits
radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique
du ministère des Communications du Canada.