Filter
Top Products
Basic Menu
Source Select
Picture
Volume
Image Options
Projector Options
Information
Troubleshooting
Standby
Cooling down
Lamp in Nomal mode
Lamp in Eco mode
One minute after lamp is turned on
Retrying to turn on lamp
Lamp has reached its end of life
(2000 hours or over : Normal mode)
(3000 hours or over : Eco mode)
Lamp life has reached its end of life
(2100 hours or over : Normal mode)
(3100 hours or over : Eco mode)
Lamp or filter cover error
(3 locations)
Temperature error
Fan error
Lamp error
Power/ Status Light Messages
Condition
Steady orange
Blinking green
Steady green
Steady green
Blinking green
Steady green
Steady green
Steady orange
Steady orange
Steady orange
Steady orange
Steady orange
–
–
–
Steady green
Depending Lamp mode
Blinking orange
Steady red
Steady red
Blinking red
(1 sec interval)
Blinking red
(4 sec interval)
Blinking red
(8 sec interval)
Blinking red
(12 sec interval)
–
Blinks green for 60 seconds.
–
–
Do not turn off the projector during
this condition.
The projector retries 3 times at an
interval of 15 sec for max. 45 sec).
Message appears on screen during
this condition. The projector reaches
its end of life. Please replace the
lamp as soon as possible.
The projector is in standby mode and
cannot be turned on.
The projector is in standby mode and
cannot be turned on.
The projector is in standby mode and
cannot be turned on.
The projector is in standby mode and
cannot be turned on.
The projector is in standby mode and
cannot be turned on.
Power Indicator
Status Indicator
Note
Common Problems & Solutions
Does not turn on
No picture
Image isn’t square to the screen
Picture is blurred
Image is scrolling vertically,
horizontally or both
Remote control does not work
Status indicator is lit or blinking
Cross color in RGB mode
• Check that the power cable is plugged in and that the power button on the
projector cabinet or the remote control is on.
• Ensure that the lamp cover is installed correctly. See page E-38.
• Check to see if the projector has overheated or the lamp usage exceeds 2100
hours (3100 hours in Eco mode). If there is insufficient ventilation around the
projector or if the room where you’re presenting is particularly warm, move the
projector to a cooler location.
• Use the menu to select your source (Video, S-Video or RGB). See page E-31.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-31.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Factory
Default on the Image Options Menu. See page E-33.
• Reposition the projector to improve its angle to the screen. See page E-28.
• Use the Keystone on the Image Options Menu to correct the trapezoid distortion.
See page E-31.
• Adjust the focus. See page E-27.
• Reposition the projector to improve its angle to the screen. See page E-28.
• Ensure that the distance between the projector and screen is within the
adjustment range of the lens. See page E-17.
• Use menus or Source button on the remote control or the cabinet to select the
source you want to input.
• Install new batteries. See page E-13.
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page E-13.
• Make sure that you are in the Projector mode or the PJ button lights in red. If not,
press the PJ button.
• See the Power/ Status Light messages.
• If Auto Adjust is off, turn it on. If Auto Adjust is on, turn it off and balance the image
with the Position and Clock Adjust on the Advanced Options Menu. See page
E-33.
Problem Check These Items
Basic Menu
Normal/Eco
RGB
Video
S-Video
Menu
Setup
* This setting is optional. you need the optional presentation
remote control (PR51KIT).
Source Select
Picture
Projector Options
Brghtness
Contrast
Color
Hue
Sharpness
Image Options
Menu
Menu Mode
Language
Source Display
No Input Display
Volume Bar
Keystone Bar *
Filter Clean Message
Menu Display Time
Setup
Orientation
Cinema Position
Background
Page 1 (Source Index/Input Terminal/Horizontal Frequency/Vertical Frequency/Sync
Polarity)
Page 2 (Signal Type/Video Type/Sync Type/Interlace)
Page 3 (Remaining Lamp Time/Lamp Hour Meter/Projector Usage)
Keystone
Lamp Mode
Factory Default
Desktop Front/Ceiling Rear/
Desktop Rear/Ceiling Front
Top/Center/Bottom
Blue/Black/Logo
Basic/Advanced
English/German/French/
Italian/Spanish/Swedish/
Japanese
On/Off
On/Off
On/Off
On/Off
On/Off
Manual/Auto 5 sec/Auto 15
sec/Auto 45 sec
Volume
All Data/Current Signal
Information