Omnitron Systems Technology CWDM/X Network Card User Manual


  Open as PDF
of 2
 
iConverter CWDM/X
2 and 4 Channel Single-Fiber MUX/DEMUX
USER MANUAL
Product Overview
The
iConverter Single-Fiber Course Wave Division
MUX/DEMUX CWDM/X modules utilize a single-
fiber Common Port that aggregates two different
wavelengths from each dual ber Channel Port. Each
ber strand on the Channel Port supports a different
wavelength, one wavelength for transmit (Tx) and a
different wavelength for receive (Rx).
Single-Fiber CWDM/X modules are always used in
pairs (example: model 8870-0 used with 8871-0). The transmit wavelength of the Channel
Port at one end must match the receive wavelength of the same Channel Port at the other
end, and the receive wavelength of the Channel Port at one end must match the transmit
wavelength of the same Channel Port at the other end.
2-Channel CWDM/X modules support four wavelengths; two transmit and two receive.
4-Channel Single-Fiber CWDM/X modules support eight wavelengths and feature an optional
Expansion Port (EXP) that can be used to cascade two MUX/DEMUX modules, doubling the
channel capacity from 4-Channels to 8-Channels on the single-ber link.
Port Denitions
Figure 1: Port Locations for 2-Channel CWDM/X Module
Figure 2: Port Locations for 4-Channel CWDM/X Module
Model Numbers
Warranty
WARNING
The operating description in this Instruction Manual is for use by qualied personnel only. To avoid electrical shock, do not perform any
servicing of this unit other than that contained in the operating instructions, unless you are qualied and certied to do so by Omnitron
Systems Technology.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of ONE YEAR from the date
of shipment. You may register your product on the Internet at http://www.omnitron-systems.com. During the warranty period, Omnitron
will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping
charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by
Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modications or tampering with equipment (including removal
of equipment cover by personnel not specically authorized and certied by Omnitron), or misuse, or operating outside the environmental
specication of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site
preparation or maintenance.
No other warranty is expressed or implied. Omnitron specically disclaims the implied warranties of merchantability and tness for any
particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or any legal theory.
040-08870-001A 1/09
Page 1
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
Model Type
Model
Number
Channel Port
ITU Center Wavelength (nm)
Tx/Rx
Expansion
Port
2-Channel
MUX/DEMUXw
8870-0 1471/1491, 1511/1531 No
8871-0 1491/1471, 1531/1511 No
8872-0 1551/1571, 1591/1611 No
8873-0 1571/1551, 1611/1591 No
4-Channel
MUX/DEMUXw
8874-0 1271/1291, 1311/1331, 1351/1371, 1431/1451 No
8875-0 1291/1271, 1331/1311, 1371/1351, 1451/1431 No
8874-1 1271/1291, 1311/1331, 1351/1371, 1431/1451
Yes
1
8875-1 1291/1271, 1331/1311, 1371/1351, 1451/1431
Yes
1
8876-0 1471/1491, 1511/1531, 1551/1571, 1591/1611 No
8877-0 1491/1471, 1531/1511, 1571/1551, 1611/1591 No
8876-1 1471/1491, 1511/1531, 1551/1571, 1591/1611
Yes
2
8877-1 1491/1471, 1531/1511, 1571/1551, 1611/1591
Yes
2
sSingle-ber CWDM/X models must be used in pairs. The Tx wavelengths on one end has to match the Rx wavelengths
on the other.
1
EXP port supports 1471nm to 1611nm. Use with 8870-0, 8871-0, 8872-0, 8873-0, 8876-0 or 8877-0.
2
EXP port supports 1271nm to 1451nm. Use with 8874-0 or 8875-0.