Filter
Top Products
REVISION HISTORY
Manual # Date Comments
C1919M 9/97 Original version.
C1919M-A 3/00 Revised installation instructions and Figure 1. Added Figure 2.
C1919M-B 7/00 Corrected RX polarity in Figure 1.
C1919M-C 11/00 Revised drawings to reflect label change.
® Pelco, the Pelco logo, Spectra, Genex, Legacy, Coaxitron, and PelcoVision are registered trademarks of Pelco. © Copyright 2000, Pelco.
™ Esprit and Camclosure are trademarks of Pelco. All rights reserved.
Testing (Refer to PV1000 Instruction/Operation Manual)
1. Ensure that the PV1016 Transmitter DIP switch settings or the PV1004 Transmitter programming are correct for the telemetry type
required by the receiver.
2. Ensure that the PV1000 Transmitter is properly programmed for the COM 2 port baud rate and parity required by the receiver.
3. Confirm receiver PTZ control from a PV1016 Transmitter with front panel keyboard (while off-line) or from the PV1016 Receiver
(while on-line). Check for smooth operation.
Common Causes for Control Problems
No Control
• Transmitter DIP switch settings or programming incorrect for
receiver type.
• Transmitter COM 2 port baud rate and/or parity programming
incompatible with receiver type.
• Converter-to-receiver twisted pair connections reversed or
wired incorrectly.
• Power supply +12 VDC and GND connections to converter
reversed.
Erratic Control
• Cabling between converter and receiver incompatible with
RS-422 operation.
• Wire distance between converter and receiver requires suitable
termination at receiver.
• Wire distance between converter and receiver exceeds
4,000 feet.
• Video coax cable has Coaxitron
®
or other “up-the-coax”
control information present.
Figure 2. RS-422 Circuit
Wiring Diagram
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment. Excep-
tions to this warranty are as noted below:
• Three years on Genex
®
Series (multiplexers, server, and keyboard).
• Two years on cameras and all standard motorized or fixed focal length lenses.
• Two years on Legacy
®
, Camclosure™ Camera Systems, CM6700/CM8500/
CM9500/CM9750/CM9760 Matrix, PelcoVision
®
, DF5 Series and DF8 Fixed Dome
products.
• Two years on Spectra
®
and Esprit™, including when used in continuous motion
applications.
• Two years on WW5700 series window wiper (excluding wiper blades).
• Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to
Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss result-
ing from the specific use or application made of the Products. Pelco’s liability for any
claim, whether based on breach of contract, negligence, infringement of any rights
of any party or product liability, relating to the Products shall not exceed the price
paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any
special, incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the
product when returned.
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the
factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair). Goods returned
for repair or credit should be clearly identified with the assigned CA/RA number and
freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.
Ship freight prepaid to: Pelco
3500 Pelco Way
Clovis, CA 93612-5699
WARRANTY AND RETURN INFORMATION
PV130
TX-
TX+
RX-
RX+
GND
100 100
RX-
RX+
TX-
TX+
GND
RS-422