Seagate ST9300403SS Computer Drive User Manual


 
Savvio 10K.3 SAS Product Manual, Rev. G 53
12.3.1 Inquiry data
Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
Table 8: Savvio inquiry data
Bytes Data (hex)
0-15 00 00 xx** 12 8B 00 PP 0A 53 45 41 47 41 54 45 20 Vendor ID
16-31 [53 54 39 33 30 30 36 30 33 53 53] 20 20 20 20 20
Product ID
32-47 R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00
48-63 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
64-79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80-95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
96-111 00 43 6F 70 79 72 69 67 68 74 20 28 63 29 20 32* *Copyright
112-127 30* 30* 36* 20 53 65 61 67 61 74 65 20 41 6C 6C 20
notice
128-143 72 69 67 68 74 73 20 72 65 73 65 72 76 65 64 20
* Copyright year (changes with actual year).
** SCSI Revision support. See the appropriate SPC release documentation for definitions.
PP 10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R# Four ASCII digits representing the last four digits of the product firmware release number.
S# Eight ASCII digits representing the eight d
igits of the product serial number.
[ ] Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9300
603SS.
Refer to the values below for the values of bytes 16 through 26 of you particular model:
ST9300603SS 53 54 39 33 30 30 36 30 33 53 53
ST9
300503SS 53 54 39 33 30 30 35 30 33 53 53
ST9300403SS 53 54 39 33 30 30 34 30 33 53 53
ST9146803SS 53 54 39 31 34 36 38 30 33 53 53
ST9146703SS 53 54 39 31 34 36 37 30 33 53 53
ST9146603SS 53 54 39 31 34 36 36 30 33 53 53
12.3.2 Mode Sense data
The Mode Sense command provides a way for the drive to repo
rt its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
1. Default values
Default values are hard-coded in the drive firmware stor
ed in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2. Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
a
re allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
When power is applied to the drive, it takes saved values fro
m the media and stores them as current val-
ues in volatile memory. It is
not possible to change the current values (or the saved values) with a Mode