Filter
Top Products
Router Functions
Case 1 The Internet Gateway is shown as a network
connection. What does this mean?
It means that the Router Unit is recognized as the Internet Gateway. If you disconnect the Router Unit
from the network, the indication disappears.
Case 2 Cannot connect to the Internet
Are the WAN settings correct?
Select from the following depending on the connection method specified by your Internet service
provider.
• When connecting by DHCP (having an IP address assigned to the computer automatically), select
“Obtain an IP address automatically”. In this case, please confirm the DHCP client ID (in cases
where it is particularly specified).
• When connecting by a fixed IP address (manually assigning the computer IP address), select “Use the
following IP address”. In this case, enter the IP address for your computer specified by your Internet
service provider.
Refer to the separate Quick Start Guide for details.
Case 3 I changed the LAN settings of the Router Unit, but
I can no longer connect to the Router Unit or
network
See “Case 1: No communication between the computer and Wireless Broadband Router”, item 4 to
release and renew the IP address of your computer so that it matches the LAN settings of the Router
Unit. Alternately, you can restart the Router Unit, which automatically releases and renews the IP
address of your computer.
Note
In “Case 1: No communication between the computer and Wireless Broadband Router”, item 4, we recommend
that you release and renew the IP address only when it is “0.0.0.0” or it starts with “169.254”. In the case above, you
must release and renew the IP address, regardless of the displayed address.
Access Point Functions
Case 1 Clicked the “Refresh” button under “Access Point
List”, but nothing appears in the list
1 Did you wait long enough?
The scanning process may take some time. After clicking “Refresh”, wait at least 30 seconds
before checking the results.
2 Can the IP address of the computer be acquired?
See “Preparations”, “Case 1: No communication between the computer and Wireless Broadband
Router”, item 4.
3 Is the Access Point connected correctly to the Router Unit?
Make sure that connections are as shown.
4 Is the Windows XP “Internet Connection Firewall” function
enabled?
See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings” for details.
Case 2 Several Access Points are listed, but I do not
know which one to select
The “Access Point List” shows the MAC addresses of all the Access Points found.
Use the MAC address to identify the Access Point.
Check the MAC address of the Access Point to which you want to connect. The MAC address is
located on the label inside the rear cover of the Wireless Unit.
Case 3 The user name and password input dialog box
appears despite the lack of settings
Enter “admin” in the “User name” text box, and then click “OK”. Do not enter anything in the
“Password” text box.
Case 4 Unable to connect after Access Point functions
settings are made
Did you change the wireless connection settings of the computer
to match the Access Point functions settings?
If the network name (SSID) and security settings of the Access Point are changed, the wireless
connection settings of the computer must be changed accordingly. For information on how to do this,
refer to the documentation of the wireless LAN PC card or the Wireless LAN Converter.
Case 5 If “Easy Setup” is used after “Advanced Setup”,
what about items not included in “Easy Setup”?
If you reconfigure the unit with “Easy Setup” after using “Advanced Setup”, the items not included in
“Easy Setup” are set as follows.
Item Setting
Frequency (Channel) 2.4 GHz (Auto Select)
Broadcast Network Name (SSID) Yes
IEEE 802.11 Mode 11g, 11b (High multicast rate)
Super A/G Disable
Turbo Mode Disable
Access Control Accept all
Connection Method Obtain IP address automatically (DHCP)
Speed Auto-Detect
Setup Switch Enable
The Super A/G and Turbo Mode functions of the PCWA-AR800 are supported by the Wireless
LAN Converter PCWA-DE80 and Wireless LAN PC Card PCWA-C800S. Compatibility of the
Super A/G and Turbo Mode functions with third party Wireless Client devices is not guaranteed.
Cable modem or
DSL modem
Miscellaneous
Case 1 Forgot settings
Reset the Access Point and/or Router Unit, as described below.
To perform a reset, the Wireless Broadband Router must be on. It is possible to reset both units or only
the unit for which you have forgotten the settings. When you forget the Access Point settings, press the
Reset switch on the Wireless Unit. When you forget the Router Unit settings, press the Reset switch on
the Router Unit. Hold the switch for at least a second, and then release it.
The Wireless Broadband Router restarts automatically, and the settings of the unit whose Reset switch
is pressed revert to their factory defaults. Repeat the setup procedure.
Wireless Unit Router Unit
Note
When resetting the Access Point, be careful not to press the Quick Setup switch by mistake.
Case 2 The power cord is plugged to the AC outlet, but
the indicators do not light
1 Is the AC adapter power switch on?
zHint
When the AC adapter power switch is on, the LED on the adapter is lit.
2 Is the “Status Indicator” setting of the Access Point set to
Off?
Open the Setup Page of the Access Point, go to the Access Point “Management” page, and set
“Status Indicator” to On.
1
Click “Status Indicator” and “Change”.
2
Select “On” from the list and click “Execute Setup”.
3
When the completion message appears, click “Close”.
Reset switch
Quick Setup switch
Reset switch
To power outlet
Case 3 After pressing the Quick Setup switch, the Status
indicator starts flashing red
If the Quick Setup switch is held down for more than one second, the Status indicator starts to flash red.
30 seconds later, the Status indicator begins flashing slowly white to indicate normal operaton.
Note
The Quick Setup switch is used in setting the separately available Wireless LAN Converter PCWA-DE80 or
PCWA-DE30.
For information on how to use the Quick Setup switch, refer to Wireless LAN Converter PCWA-DE80
or PCWA-DE30 Quick Start Guide.
Case 4 Computer firewall function and browser proxy
settings
■ The “Internet Connection Firewall” function is enabled
When the Windows XP “Internet Connection Firewall” function is enabled, it may prevent the
computer from being accessed externally (this function is disabled by default). This function can
prevent connection to your network when you change your Wireless LAN Converter or Access
Point settings. If this happens, disable the “Internet Connection Firewall” function as described
here, connect to the network, and then re-enable the function.
1 Click “Start”, and then click “Control Panel”.
2 In “Control Panel”, click “Network and Internet Connections”, and then click “Network
Connections”.
zHint
If “Network and Internet Connections” does not appear, click “Switch to Category View” on the left.
3 In the “Network Connections” window, right-click the icon of the wireless network that
you want to use, and click “Properties”.
4 Click the “Advanced” tab and (if selected) clear the “Protect my computer and network
by limiting or preventing access to this computer from the Internet” check box.
5 Click “OK”.
Refer to Windows XP Help for details about the “Internet Connection Firewall” function.
Note
Make sure that you take appropriate security measures when the “Internet Connection Firewall” function is
disabled. Except when configuring the Access Point, it is strongly recommended that you enable the “Internet
Connection Firewall” function at all times.
■ When using a personal firewall software provided standalone
or as part of an antivirus or network security software
Antivirus scanning and network security software sometimes includes a function called a
“personal firewall”, intended to prevent unauthorized access by other computers. Depending on
the software, the security level of this function may initially be set to a high level. If this high
security level setting is left enabled, other computers may be unable to access your computer. This
can cause problems such as not being able to connect to the network when changing the Wireless
LAN Converter or Access Point settings. In this event, lower the security level to allow the
network connection. Refer to the software instructions or Help for details.
Notes
• Make sure that you take appropriate security measures.
• For questions about firewall functions, contact your firewall software manufacturer.
■ Proxy settings
Make sure that no proxy settings are enabled for the IP address of the Wireless Broadband Router.
Note
While the proxy server settings are disabled, it may not be possible to display other pages except the Wireless
Broadband Router Setup page.
Example 1: Using Microsoft Internet Explorer
1 On the “Tools” menu, click “Internet Options”.
The “Internet Options” dialog box appears.
2 On the “Connection” tab, click “LAN Settings”.
The “Local Area Network (LAN) Settings” dialog box appears.
zHint
If there are dial-up profiles in the “Dial-up” box, make sure that you select the “Never dial a connection”
check box.
3 If the “Use a proxy server for your LAN (These settings do not apply to dial-up or VPN
connections)” check box is selected, clear the check box and click “OK”.
4 When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
Example 2: Using Netscape
1 Start the Web browser on the computer used for the Wireless Broadband Router
setup.
2 On the “Edit” menu, click “Preferences”.
3 In “Category”, click “Advanced” and click the “Proxies” button.
4 Select “Direct connection to the Internet” and click “OK”.
5 When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
■ Java settings
Make sure that the Java settings of your Web browser are enabled. If they are not, do so.