Filter
Top Products
4
Using Your Monitor
Preset and User Modes
The Multiscan 100ES/200ES has factory preset modes for the 8 most
popular industry standards for true “plug and play” capability.
For less common modes, the Multiscan 100ES/200ES’s Digital
Multiscan Technology will perform all of the complex adjustments
necessary to ensure a high quality picture for any timing between
30 and 70␣ kHz.
CPD-100ES/100EST and CPD-200ES/200EST
For customers using Windows
4)
95/98
To maximize the potential of your monitor, install the new model
information file from the supplied Windows Monitor Information
Disk onto your PC.
This monitor complies with the “VESA DDC” Plug & Play
standard. If your PC/graphics board complies with DDC, select
“Plug & Play Monitor (VESA DDC)” or this monitor’s model name
as the monitor type in the “Control Panel” of Windows 95/98. If
your PC/graphics board has difficulty communicating with this
monitor, load the Windows Monitor Information Disk and select
this monitor’s model name as the monitor type.
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 µsec.
Horizontal blanking width should be: >3.6 µsec. (Multiscan 100ES)/
>3.0 µsec. (Multiscan 200ES).
Vertical sync width should be: < 560 µsec.
Note
CPD-100ES/100EST and CPD-200ES/200EST does not apply to
Macintosh 21" color mode.
No.
1
2
3
4
5
6
7
8
Horizontal
Frequency
31.5 kHz
43.3 kHz
46.9 kHz
53.7 kHz
49.7 kHz
60.0 kHz
68.7 kHz
64.0 kHz
Resolution
(dots × lines)
640 × 480
640 × 480
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
1280 × 1024
Graphics
Mode
VGA
1)
Graphic
VESA
2)
VESA
2)
VESA
2)
Macintosh
3)
16" Color
VESA
2)
VESA
2)
VESA
2)
Vertical
Frequency
60 Hz
85 Hz
75 Hz
85 Hz
75 Hz
75 Hz
85 Hz
60 Hz
Getting Started
Before using this monitor, please make sure that the following
items are included in your package: Multiscan 100ES/200ES
monitor (1), power cord (1),
“Windows Monitor Information
Disk
” (1), and this operating instruction manual (1).
This monitor will sync with any IBM or compatible system
equipped with VGA or greater graphics capability. Although
this monitor will sync to other platforms running at horizontal
frequencies between 30 and 70 kHz, including Macintosh and
Power Macintosh system, a cable adapter is required. Please
consult your dealer for advice on which adapter is suitable for
your needs.
Step 1: With the computer switched off, attach the video
signal cable to the video output.
Step 2: Attach the power cord to the monitor and the other
end to a power outlet.
Step 3: Turn on the monitor and computer.
Step 4: If necessary, adjust the user controls according to
your personal preference.
The installation of your Multiscan 100ES/200ES is complete.
Enjoy your monitor.
1) VGA is a trademark of IBM Corporation.
2) VESA is a trademark of the non-profit organization, Video
Electronics Standard Association.
3) Macintosh is a trademark of Apple Computer Inc.
4) Windows
®
is a registered trademark of Microsoft
Corporation in the United States and other countries.
to video output
IBM or compatible
computer
Macintosh or compatible
computer
to video output
to a power outlet
Macintosh adapter (not supplied)
Power cord (supplied)