Filter
Top Products
1-1
SECTION 1
GENERAL
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
A
b
c
B
a
a
b
English
Setup
This USB unit provides a fast and easy way to connect USB compliant peripheral devices
(such as a mouse, keyboards, printers, and scanners) to your computer using a
standardized USB cable.
1
Turn “on” the power of your computer and any self-powered USB compliant
peripheral devices.
2
Connect one end of the AC power cord to the unit (fig. A-a), and the other end
to a power outlet.
3
Turn “on” the power switch. (fig. A-b)
4
Connect the square end of the supplied USB cable to the unit’s square
connector. (fig. A-c)
Then connect the rectangular end to your computer.
If the LED is green (fig. B-b), you are ready to use the USB unit. If the LED is orange,
see “Troubleshooting” on the reverse page.
For customers using Windows
®
If a message appears on your screen, follow the on-screen instructions and select Generic
USB Hub as the default setting.
5
Connect your peripheral devices to the rectangular USB connectors. (fig. B-
a)
To set the unit on its side:
Attach the supplied rubber feet (2) to the holes on the side of the unit. (fig. C-a)
Then attach the stand by inserting the nibs into the slots on the unit. (fig. C-b)
Make sure that the word FRONT on the stand is facing the side of the unit with the LED.
You can stand the unit on either of its sides.
Notes:
• This hub unit is not guaranteed to work with all USB peripheral devices.
• The unit does not include driver software for individual USB devices. In most cases, USB
driver software needs to be installed on the host computer. Refer to the peripheral device’s
instruction manual for further details. (This unit does not require special software to
operate.)
• Not all computers and /or operating systems support USB configurations. If you are using
Windows
®
, the version must be OSR 2.1 or later and have USB support. Check your
computer’s instruction manual to see if you can connect USB devices.
• If you connect a keyboard or mouse to the USB connectors and then boot your computer for
the first time, the peripheral devices may not function. First connect the keyboard and mouse
directly to the computer and setup the USB compliant devices.
C
a
b
• Windows
®
is registered trademark of Microsoft Corporation in the United States
and other countries.
• All other product names mentioned herein may be the trademarks or registered
trademarks of their respective companies.
• Furthermore, “™” and “®" are not mentioned in each case in this manual.
English
Troubleshooting
The LED is not lit
• Turn “on” the power switch. The unit must be “on” to work as a hub for USB
peripheral devices.
The LED is orange
• Check that the USB cables are securely connected to the unit.
• Check that the USB port is enabled on the host computer’s basic input/output
system (BIOS). Refer to your computer’s manual to change the port setting.
Individual USB peripheral devices do not work
• If the connected USB peripheral device uses software, install the software on the host
computer.
• Turn the unit’s power switch “off” and “on.” If your USB peripheral devices are self-
powered, turn their switches “off” and “on” as well.
• Check that the connectors are secure in their sockets.
• Install the latest version of the device driver on your computer. Contact your
device‘s manufacturer for information about the appropriate device driver.
For customers using Windows
®
95
If you are having trouble using this USB unit, try the steps below.
1. Right-click on My Computer and select Properties.
2. Click on the Device Manager tab. Scroll down and select Universal Serial Bus
Controller.
/ If Universal Serial Bus Controller does not appear, you need to load a USB
supplement disk. Contact your computer’s manufacturer for more information
about obtaining a USB supplement disk.
3. Select Generic USB Device from the USB controller list and click on Properties. If
there is a check in the box next to “Disable in this hardware profile,” remove the
check.
4. Click on Refresh.