Toshiba TDP-D1 Projector User Manual


 
21
Operations
20
1
Turn on the power.
Turn on the power, following the instructions in Turning on the power
p.19
.
2
Select language (When using for first time).
When the projector is used for the first time after purchase, a message is displayed on
the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step
6
.)
q Use the buttons to select the desired
language, and press the button.
A message displays the selected language.
w Press the button to erase the message.
Notes
After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu
p.29
select Reset all to display the
Language menu the next time the projector is turned on.
The language can also be set via the Display setting menu
p.29
.
This owners manual assumes that English has been selected.
3
Place connected device(s) in operating status.
Turn on and boot up connected computers and other devices.
Select Cancel or install driver contained in the supplied CD-ROM, when the dialog
box of the Add New Hardware Wizard screen appears on the computer when
connecting a computer. (The supplied CD-ROM contains a driver information file
named TOSHIBA_TDP.inf. Click the Browse button of the dialog box to find and
designate this file.)
4
Select input.
q Press the INPUT button.
A list of inputs appears on the screen.
w Use the buttons to select the desired
input, and press the button.
The picture for the selected input is projected.
Basic operations
English
Français
Português
Deutsch
Italiano
Español
................
..............
..............
................
...............
..........
...................
.......
.......
...................
English
French
German
Italian
Spanish
Portuguese
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Computer
Y/P
B
/P
R
Video
S-video
Turning the power on and off (Continued)
Notes
The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu
p.29
.
The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed
p.21
.
Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling complete
FAN TEMP LAMP ONFAN TEMP LAMP ON
A
FAN TEMP LAMP ON
B C
(Green) (Green) (Orange)
Flashing
(Green) (Off) (Orange)
(Off) (Off) (Orange)
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord or turning off the main
power switch in this state will shorten the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
C
In standby mode
Note
The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
PRECAUTIONS
Before unplugging the power cord or turning off the main power switch, make sure that
the LAMP indicator is off. Unplugging the power cord or turning off the main power
switch and cutting off the power while the projector is running or being cooled will
shorten the life of the lamp. However, please unplug the power cord if the projector
locks up or acts abnormally.
If the power cord is unplugged before cooling is complete, give the lamp time (about 10
minutes) to cool before plugging it back in. If the lamp overheats it may fail to light, and
its lifetime will be shortened.
D
R
A
G
R
-
C
L
I
C
K
L
-
C
L
I
C
K
RESIZE OFF
INPUT
MENU
VOL.+VOL.
-
RESIZE
INPUT
ON/STANDBY INPUT
MENU
ON LAMP TEMP FAN
AUTO KEYSTONE AUTO SET
VOL.
+
VOL.
-
Control panel
Remote
Control