Filter
Top Products
3
Tel/Modem, Ethernet and Coaxial Connections
Connect Your Equipment to the Power Conditioning Center's Tel/Modem Jacks:
Connect a phone cable from the wall jack directly to the Power Conditioning Center's
RJ-style phone jack labeled “IN.” Connect a phone cable from the Power
Conditioning Center's RJ-style phone jack labeled "OUT" directly to the device to be
protected. HT7300PC models feature two “OUT” jacks; either one or both of the jacks
may be used, but protection is for a device or devices sharing a single line only. The
Power Conditioning Center must always be the first item connected in line from the
wall jack. The Power Conditioning Center must be plugged into a 3-wire, grounded
AC outlet for phone line surge protection to work.
Connect Your Equipment to the Surge Suppressor's Network Jacks:* Connect a
data cord from the wall jack or cable/DSL modem directly to the Power Conditioning
Center's network jack labeled “IN.” Connect a data cord from the Power Conditioning
Center's network jack labeled “OUT” directly to the device to be protected. The
Power Conditioning Center must always be the first item connected in line from the
Ethernet source (typically a wall jack). The Power Conditioning Center must be
plugged into a 3-wire grounded AC outlet for network line surge protection to work.
* 10/100 BaseT/TX, Token Ring. Not compatible with PoE (Power Over Ethernet) applications
Connect Your Equipment to the Power Conditioning Center's Coaxial Jacks:
Connect a coaxial cable from the wall jack directly to the Power Conditioning
Center's “F” style coaxial jack labeled “IN.” Connect a coaxial cable from the Power
Conditioning Center's “F” style coaxial jack labeled “OUT” directly to the device to
be connected. Additional sets of coaxial jacks allow for simultaneous connection and
protection of additional devices on additional lines (cable, antenna or satellite). Make
sure that each device and its corresponding wall jack are connected to corresponding
“IN” and “OUT” jacks on the Power Conditioning Center. The Power Conditioning
Center must always be the first item connected in line from the coaxial wall jack. The
Power Conditioning Center must be plugged into a 3-wire grounded AC outlet for
coaxial line surge protection to work. Make sure coax cables connected to satellite
dishes, antennas, etc. are also grounded.
IR Outlet Control
Manual Control
Turn Controllable IR Outlets ON or OFF
• STEP 1: Momentarily press the “SELECT” Switch to choose which IR outlet you
wish to select. The corresponding “OUTLET SELECT” LED will flash to
indicate which outlet you have selected. Each time you press the switch, it will
select the next LED in line.
• STEP 2: To turn IR outlet ON: When an outlet is selected using the “SELECT”
Switch, momentarily press the "ENTER" Switch to turn the outlet ON. The
corresponding “POWER ON” LED will illuminate to indicate power is ON at the
outlet. The corresponding “OUTLET SELECT” LED will illuminate
continuously to indicate the outlet is no longer selected. To turn IR outlet OFF:
Momentarily press the “SELECT” Switch to choose which IR outlet you wish to
turn off. The corresponding “OUTLET SELECT” LED will flash to indicate
which outlet you have selected. Momentarily press the “ENTER” Switch to turn
the outlet OFF. The corresponding “POWER ON” LED will go off to indicate
power is OFF at the outlet. The corresponding “OUTLET SELECT” LED will
also go off.
Set Delay Interval for Remote IR Outlet Power ON or Power OFF
Using a small tool, set the DIP switches to select the delay interval (0, 1, 10 or 30
seconds) when turning on or off multiple IR outlets in a sequence using a remote. See
chart for settings.
DIP Switch 1 DIPSwitch 2
Delay Interval Position Position
0 seconds DOWN DOWN
1 second
(Factory Setting) UP DOWN
10 seconds DOWN UP
30 seconds UP UP
Remote Control (With Included IR Remote)
All remotes require unobstructed access to the IR sensor located
on the front panel of the Power Conditioning Center.
Turn All Controllable IR Outlets ON
Momentarily press the remote’s “ALL ON” button, and then
press the “ENTER” button. The IR Outlets will turn ON in the
following sequence: 1, 2, 3, 4.
Turn All Controllable IR Outlets OFF
Momentarily press the remote’s “ALL OFF” button, and then
press the “ENTER” button. The IR Outlets will turn OFF in the
following sequence: 4, 3, 2, 1.
Turn Individual Controllable IR Outlets ON or OFF
Momentarily press the number button on the remote (1, 2, 3 or
4) that corresponds to the IR Outlet you wish to control, and then
press the "ENTER” button.
Remote Control
(With User-Supplied Universal Learning IR Remote)
Use the included IR remote to program a user-supplied universal learning IR remote.*
Follow the programming instructions for the user-supplied remote. All remotes
require unobstructed access to the IR sensor located on the front panel of the Power
Conditioning Center.
* The user-supplied remote must be a universal learning type to work with the included remote.
Optional Installation
200605132 93-2557 HT7300PC OM V2.qxd 10/26/2006 3:27 PM Page 3