Winegard RV-7012 Power Supply User Manual


  Open as PDF
of 2
 
Figure 3
APPLICATIONS AND
ALTERNATE CONNECTIONS
INSTRUCTIONS
STEP 1. Select location for wall plate and
patio receptacle. Run two coax cables between
locations and install connectors on each end.
Mark cables so "cable input" and "TV output"
may be identied. Antenna downlead and
+12 VDC will also be needed at inside wall
plate/power supply location.
STEP 2. The wall plate/power supply assembly
may be ush mounted in most standard electrical
boxes. To ush mount cut a hole in wall to t the
box. Run 2 #12 wires between wall plate/power
supply and +12VDC source and route downlead
cable to this location. Install cable between set 2
outlet and power supply location at this time.
WHEN CONNECTING CABLE OR WIRES
BE SURE SWITCH IS IN OFF POSITION.
STEP 3. Make +12 volt connection to wall
plate/power supply Figure 2. Install terminals
on wires from +12VDC source as shown in
Figure 1. Crimp terminals with Craftsman type
4 crimping tool or equivalent. Push wires onto
tabs on terminal board as shown in Figure 2. If
in doubt as to the polarity of the wires, connect
them temporarily to tabs on circuit board and
press switch on front of outlet. If light comes
on, polarity is correct. See Figure 3.
STEP 4. Install connectors on downlead
and set 2 cable as shown in Figure 5. Attach
downlead cable to jack on wall plate/power
supply marked antenna as shown in Figure
4. Attach cable going to set 2 outlet to jack
on power supply marked SET 2. Attach cable
coming from cable input to jack on power supply
marked CABLE.
Figure 1
Figure 3
WARNING
DO NOT connect high
current devices such
as hair dryers to this
receptacle. Maximum
current rating of this
receptacle is 7.5 amps
at 12 VDC.
Figure 2
Connector
Insulation
Remove 1/4" of
insulation from
#12 wire.
#12 Wire
1/4"
Connector
Ferrule
Crimp Here
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
Cable Input
Cable Input
Set 2
Set 1
WARNING: Use of this on/off
power switch with any product
other than Winegard amplied
RV antenna, could result in re
or other damage.
WARNING: Do Not Connect High
Current Devices Such as Hair
Dryers to +12 Volt Receptacle
on Wall Plate/Power Supply.
Maximum current ratings of
this receptacle is 7.5 amps at
+12 VDC.
Example 1
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
SP-1002
Splitter
Example 3
Example 2
Antenna
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
ON/OFF
Switch
ON/OFF
Switch
ON/OFF
Switch
+12 VDC
Ground
Outdoor Receptacle
WA-1010
APPLICATIONS AND
ALTERNATE CONNECTIONS
INSTRUCTIONS
STEP 1. Select location for wall plate and
patio receptacle. Run two coax cables between
locations and install connectors on each end.
Mark cables so "cable input" and "TV output"
may be identied. Antenna downlead and
+12 VDC will also be needed at inside wall
plate/power supply location.
STEP 2. The wall plate/power supply assembly
may be ush mounted in most standard electrical
boxes. To ush mount cut a hole in wall to t the
box. Run 2 #12 wires between wall plate/power
supply and +12VDC source and route downlead
cable to this location. Install cable between set 2
outlet and power supply location at this time.
WHEN CONNECTING CABLE OR WIRES
BE SURE SWITCH IS IN OFF POSITION.
STEP 3. Make +12 volt connection to wall
plate/power supply Figure 2. Install terminals
on wires from +12VDC source as shown in
Figure 1. Crimp terminals with Craftsman type
4 crimping tool or equivalent. Push wires onto
tabs on terminal board as shown in Figure 2. If
in doubt as to the polarity of the wires, connect
them temporarily to tabs on circuit board and
press switch on front of outlet. If light comes
on, polarity is correct. See Figure 3.
STEP 4. Install connectors on downlead
and set 2 cable as shown in Figure 5. Attach
downlead cable to jack on wall plate/power
supply marked antenna as shown in Figure
4. Attach cable going to set 2 outlet to jack
on power supply marked SET 2. Attach cable
coming from cable input to jack on power supply
marked CABLE.
Figure 1
Figure 3
WARNING
DO NOT connect high
current devices such
as hair dryers to this
receptacle. Maximum
current rating of this
receptacle is 7.5 amps
at 12 VDC.
Figure 2
Connector
Insulation
Remove 1/4" of
insulation from
#12 wire.
#12 Wire
1/4"
Connector
Ferrule
Crimp Here
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
Cable Input
Cable Input
Set 2
Set 1
WARNING: Use of this on/off
power switch with any product
other than Winegard amplied
RV antenna, could result in re
or other damage.
WARNING: Do Not Connect High
Current Devices Such as Hair
Dryers to +12 Volt Receptacle
on Wall Plate/Power Supply.
Maximum current ratings of
this receptacle is 7.5 amps at
+12 VDC.
Example 1
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
SP-1002
Splitter
Example 3
Example 2
Antenna
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
ON/OFF
Switch
ON/OFF
Switch
ON/OFF
Switch
+12 VDC
Ground
Outdoor Receptacle
WA-1010
APPLICATIONS AND
ALTERNATE CONNECTIONS
INSTRUCTIONS
STEP 1. Select location for wall plate and
patio receptacle. Run two coax cables between
locations and install connectors on each end.
Mark cables so "cable input" and "TV output"
may be identied. Antenna downlead and
+12 VDC will also be needed at inside wall
plate/power supply location.
STEP 2. The wall plate/power supply assembly
may be ush mounted in most standard electrical
boxes. To ush mount cut a hole in wall to t the
box. Run 2 #12 wires between wall plate/power
supply and +12VDC source and route downlead
cable to this location. Install cable between set 2
outlet and power supply location at this time.
WHEN CONNECTING CABLE OR WIRES
BE SURE SWITCH IS IN OFF POSITION.
STEP 3. Make +12 volt connection to wall
plate/power supply Figure 2. Install terminals
on wires from +12VDC source as shown in
Figure 1. Crimp terminals with Craftsman type
4 crimping tool or equivalent. Push wires onto
tabs on terminal board as shown in Figure 2. If
in doubt as to the polarity of the wires, connect
them temporarily to tabs on circuit board and
press switch on front of outlet. If light comes
on, polarity is correct. See Figure 3.
STEP 4. Install connectors on downlead and
set 2 cable as shown in Figure 5. Attach downlead
cable to jack on wall plate/power supply marked
antenna as shown in Figure 4. Attach cable going
to set 2 outlet to jack on power supply marked
SET 2. Attach cable coming from cable input to
jack on power supply marked CABLE.
Figure 1
WARNING
DO NOT connect high
current devices such
as hair dryers to this
receptacle. Maximum
current rating of this
receptacle is 7.5 amps
at 12 VDC.
Figure 2
Connector
Insulation
Remove 1/4" of
insulation from
#12 wire.
#12 Wire
1/4"
Connector
Ferrule
Crimp Here
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
Cable Input
Cable Input
Set 2
Set 1
WARNING: Use of this on/off
power switch with any product
other than Winegard amplied
RV antenna, could result in re
or other damage.
WARNING: Do Not Connect High
Current Devices Such as Hair
Dryers to +12 Volt Receptacle
on Wall Plate/Power Supply.
Maximum current ratings of
this receptacle is 7.5 amps at
+12 VDC.
Example 1
Antenna
Outdoor Receptacle
WA-1010
TV
Outlet
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
SP-1002
Splitter
Example 3
Example 2
Antenna
Antenna
Input
TG-7221
Cable
Input
Set 2
Set 1
ON/OFF
Switch
ON/OFF
Switch
ON/OFF
Switch
+12 VDC
Ground
Outdoor Receptacle
WA-1010
 previous