Filter
Top Products
Installation Preparation Document (for physical installation of the product only)
Xerox DocuTech 6100/6115/6135
701P43857
June 2005
Please ensure electrical, space, and supplies are available prior to equipment delivery.
Customer Support
The Xerox Customer Support Center is available to provide general
information, answer questions, and take service calls. You can reach
the Customer Support Center at the following toll-free phone number:
United States 1-800-821-2797
Your Xerox Analyst will provide fee-based training upon request.
Space Requirements
The diagram below is provided as a representation only of the space
envelope required for installation of Xerox equipment. Diagram is a
representation only and not drawn to scale.
WIDTH
DocuTech 61xx
Representation only.
D
E
P
T
H
Note: The 6100, 6115, 6135 are available with and without a stand to
support the controller. If a stand is ordered, it will be positioned to the
left of the printer, within the service space envelope. If no stand is
ordered, the controller will be placed on the floor to the left of the
printer in the service space envelope.
Note: The dimensions shown below provide the overall service space
required, including the space to the nearest obstruction. The
dimensions are in inches and are absolute minimums.
With stand Without stand
Configuration
Width Depth Width Depth
6100, 6115, 6135
with interposer, and
Finisher
243.0" 114.0” 240.0” 114.0"
6100, 6115, 6135
without Interposer,
with Finisher
196.0" 114.0” 193.0” 114.0"
Electrical Requirements
Printer/Finisher/Binder
Line Options: Single
Source
Voltage 208/240
Amperage 50
Cycles 60 Hz
Receptacle Xerox Part No. 600S3779
Receptacle NEMA Part No. 14-50R
Power Cord Xerox Part No. 98K19950
117K9940
Receptacle Diagram
* Dedicated power outlets required. Ensure each power cord has a separate
circuit that cannot be shared with other devices.
*15 ft. power cord(s) are provided, however, the distance from the equipment
to the outlet should not exceed 13.1 ft.
Electrical Requirements
Digital Front End (DFE) Controller Platform:
Line Options: Dedicated
Voltage 110V
Amperage 15
Cycles 60 Hz
15 amp Receptacle Xerox Part No.
20 amp Receptacle Xerox Part No.
600S3704
600S3703
Receptacle NEMA Part No. 5 - 20R or 5 - 15R
Receptacle Diagram
or
• All controller configurations require a 110VAC, 15 Amp
grounded receptacle for the outlet strip that provides
receptacles
for the
controller and its peripheral devices (monitor, modem,
CDROM drive, and tape drive)
• Adapters that eliminate the ground connection to the outlet can
not be used.
• Xerox provides 15 feet of cabling with Teflon coating (Plenum
rated), to connect the controller to the Processor/Finisher.
Interposer
Line Options:
Dedicated
Voltage 120
Amperage 15
Cycles 60 Hz
Receptacle Xerox Part No. 600S3704
Receptacle NEMA Part No. 5 - 15R
Power Cord Length 6 feet
Receptacle Diagram
Installation Considerations
• There should be a minimum of 78 inches (1,981mm) clearance
from the floor to the nearest overhead obstruction.
• Mobility Assist Device - The optional mobility assist device
reduces the installation clearance required to 30
inches
(760mm) at the processor end of the printer and 15 inches (380
mm) at the finisher end.
• For proper operation, the printer must be perfectly level. The
floor must be level within 2 degrees in any direction. On floors
less than 2 degrees out of level, installation personnel install a
leveling kit to level the machine.
• If the floor is more than 2 degrees out of level, this condition
cannot be corrected by the leveling kit. Another suitable location
must be found for the printer to be installed properly.
• A minimum 50-inch clearance of exclusive operator area must
be maintained in front of each component. This space cannot
be shared.
• A minimum of 36 inches of clearance is required in the back of
each component for general service clearance.