User-Programmable Features
User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON)
Fea ture
Select
Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4
✱ 1
Add New Remote
NOTE 1
Chirps
(Off/On/Quiet*)
(1 chirp/2 chirps/3 chirps)
*Quiet chirps are only available with
SSPS Siren
AutoArming
(On/Off)
Arm/Disarm with
Secondary Remote
NOTE 5
✱ 2
Siren Sounds
(Requires SSPS Siren)
NOTE 2
NOT USED
AutoArm & Lock
(On/Off)
Trunk Release with
Secondary Remote
NOTE 6
✱ 3
Play Siren Sounds
(Requires SSPS SIren)
Remote Valet Feature
(On/Off)
NOT USED
Silent Arm/Disarm with
Secondary Remote
NOTE 6
✱ 4
Siren Duration
(30 /60/90 Seconds)
(1 Chirp/2 Chirps/3 Chirps)
AutoStart
Neither/Battery/Temperature/Both)
(1 chirp /2 chirps/3 chirps/4 chirps)
(Requires IntelliStart 4)
FACT
(Off/On)
NOT USED
✱ 5
AutoLock
(Off/On/RPM*)
(1 Chirp/2 Chirps/3 Chrrps)
(IntelliStart 4 required for RPM
dependent door locking)
NOT USED
NOT USED
Remote Start with
Secondary Remote
(Requires IntelliStart 4)
NOTE 6
✱ 6
AutoUnlock
(On/Off)
Clear All Remotes
NOTE 4
NOT USED
Window Rolldown/Venting
with Secondary Remote
(Requires
SmartWindows 4)
NOTE 6
✱ 7
Re set All to Fac tory Set tings
(ex cept re mote controls and
valet code)
NOTE 3
Valet Code
SHOULD ONLY BE PROGRAMMED
BY THE VEHICLE OWNER
NOT USED
Remote Valet Mode
with Secondary Remote
NOTE 6
n
NOTE 1: Press the button on the remote to be programmed, you will hear one chirp. Press the button again, you will hear
two chirps.
n
NOTE 2: When this feature is selected, siren sound 1 will play for five seconds. Press marked to turn the siren sound off,
press unmarked to activate the sound. Next, siren sound 2 will play for five seconds. Press marke d to turn the siren sound
off, unmarked to activate it. The system will cycle through all six siren sounds.
n
NOTE 3: You will hear two chirps when all features are reset.
n
NOTE 4: When you hear two chirps, all remote controls will have been erased from the system memory. You mu st now add
the new and/or existing remote controls to the system (i.e., AutoProgram each remote that will be u sed with the
IntelliGuard 6000).
n
NOTE 5: Programs a remote control from any other Clifford system (that uses ACG 2 technology) to arm or di sarm the
vehicle. For instance, to set the button +
✱ combination of the other car’s master remote control to arm/disarm the
system, select column 4, row 1, then transmit the +
✱ button combination from the remote you are programming. The
system will respond with one chirp. Immediately press the button combination a second time. The sys tem will respond with
two chirps. The other vehicle’s remote will now arm/disarm the system by pressing the and
✱ buttons simultaneously.
n
NOTE 6: This feature can be controlled by a secondary remote or any remote control of any other ACG 2 syst em, after that
remote has been programmed to arm/disarm this system. Select the row and column number, then transm it the unused
button on the other remote that you want to use to perform that function. The system will respond w ith the same number
of chirps as the row number. Please note that you must first set a button on the remote that will a rm/disarm the system
(column 4, row 1) before these others will be accepted.
8 In tel liGuard 6000/1298
