(C)CROSSCUTTING
1. ALWAYSRETURNTHECARRIAGETO THE
FULLREARWARDPOSITIONATCONCLUSION
OFEACHCROSSCUTTYPEOPERATION.Never
remove your hand from the Yoke Handle unless the
carriage is in this position. Otherwise the cutting
tool may climb up on the workpiece and be
propelled toward you.
2. Place guard in horizontal position and adjust
antikickback pawls to just clear the top of the fence
or workpiece, whichever is higher. This provides
additional guarding.
3. NEVER gang crosscut - lining up more than one
workpiece in front of the fence - stacked vertically,
o_ horizontally outward on the table -- and then
pulling saw thru: the blade could pick up one or
more pieces and cause a binding or loss of control
and possible injury.
4. Do not position the Arm so the operation you are
performing permits the cutting tool to extend
beyond the edges of the Table.
5. -1op-side dadoing or molding across the grain are
examples of crosscut-type cuts. The same basic
procedures including positioning of the
AKB/Spreader device as for crosscutting, apply.
(D) ACC ESSORI ES
1. Use only recommended accessories as listed on page
34.
2. Never operate this saw when equipped with a dado
head or molding head unless the molding head
guard is installed - see listing of recommended
accessories. The only exception is when "top-side"
dadoing or molding, when the sawblade guard must
be used. See detailed instructions that accompany
the dado head, molding head, and molding head
guard.
3. The use of grinding wheels, abrasive or cut-off
wheels, or wire wheels, can be dangerous and is not
recommended. (Abrasive or cut-off wheels are used
to saw many different materials including metals,
stone, and glass.)
4. Drill Chuck: Do not install or use any twist drill
larger than 1/2-inch in dia., or longer than 7 inches
in length or extending more than 6inches beyond
the chuck jaws. Do not install or use any reduced
shank drill except of the spade type (1 inch dia. or
smaller). "Use for drilling WOOD and PLASTIC
only."
NOTE: Do not overtighten arbor nut. Use the arbor wrench
to just "snug" it.
WEAR YOUR
The operation of any power tool can result in foreign
objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying
with ANSI Z87.1 (shown on Package) before commencing
power tool operation. Safety Goggles are available at Sears
retail or catalog stores.
electrical connections
POWER SUPPLY
1. Motor Specifications
The ArC motor used in this saw is a capacitor-start,
non-reversible type having the following specifications:
Voltage ............................. 120/240
Amperes .............................. 11/5.5
Hertz (cycles) ............................. 60
Phase ................................ Single
RPM .................................. 3450
Rotation as viewed from saw blade end .... Clockwise
CAUTION: Your saw is wired for 120V operation.
Connect to a 120V, 15-Amp. branch circuit and use a
15-Amp. time-delay fuse or circuit breaker. If the
motor is used for 240V operation, connect to a
15-Amp. branch circuit and use a 15-Amp. time-delay
fuse or circuit breaker.
This machine must be grounded while in use to protect
the operator from electric shock.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY A
QUALI FI ED ELECTR ICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING
OR REMOVING THE PLUG TO OR FROM THE
OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL
HAZARD OF ELECTRICAL SHOCK.
PARTICULARLY WHEN USED IN DAMP
LOCATIONS IN PROXIMITY TO PLUMBING. IF AN
ELECTRICAL SHOCK OCCURS THERE IS THE
POTENTIAL OF A SECONDARY HAZARD SUCH AS
YOUR HANDS CONTACTING THE SAWBLADE.
IF POWER CORD tS WORN OR CUT, OR DAMAGED
IN ANY WAY, HAVE IT REPLACED
IMMEDIATELY.
If your unit is for use on less than 150 volts it has a
plug that looks like below.
PROPERLY
GROUNDED OUTLET
3-PRONG PLUG
GROUNDING PRONG
This power tool is equipped with a 3-conductor cord
and grounding type plug which has a grounding prong,
Listed by Underwriters' Laboratories. The ground
conductor has a green jacket and is attached to the tool
housing at one end and to the ground prong in the
attachment plug at the other end.
This plug requires a mating 3-conductor grounded type
outlet as shown.
If the outlet you are planning to use for this power tool
is of the two prong type DO NOT REMOVE OR
ALTER THE GROUNDING PRONG IN ANY
MANNER. Use an adapter as shown and always connect
the grounding lug to known ground.
It it recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet.
