2 ELEVATIONHANDWHEEL... elevates or
lowers the blade, Turn clockwise to elevate..
counterclockwise to lower.
NOTE: Any time sawblade has been elevated
to 2-5/8 inches or higher above the table it will
be necessary to lower the blade by turning the
elevation handwheel 5 turnscounterclockwise
before tilting to bevel.
3 TiLT HANDWHEEL... tilts the blade for bevel
cutting. Turn clockwise to tilt toward left
counterclockwise to tilt toward vertical.
When the blade is tilted to the LEFT as far as it
will go, it should be at 45° to the table and the
bevel indicator should point 45 °,
NOTE: There are LIMIT STOPS on the saw
which prevent the blade from tilting beyond
45° to the LEFT and 90° to the RIGHT. (See
"Adjustments" section "Blade Tilt, or
Squareness of Blade to Table").
4 TILT LOCK HANDLE... locks the blade in the
desired tilt position. To loosen turn
counterclockwise. Push handle in and turn itto
another position if necessary in order to
tighten or loosen.
!MPORTA.NT: Be sure handle Is hanging in the
DOWN position before tilting blade. If it Is
pointing to the 1 o'clock position it may jam on
underside of the table and bend the locking
bolt,
5 RIP FENCE... is locked in place by tightening
the lock knob. To move the fence, loosen the
knob and grasp the fencewith one hand at the
fro nt.
Holes are provided in the rip fence for
attaching a wood facing when using the dado
head, or molding head.
Select a piece of smooth straight wood approx.
3/4" thick, at least as long as the rip fence, and
at least 7-1/2" wide (high)to permitclamping
of featherboards.
Attach it to the fence with three Round Head
#10 Wood Screws 2 in. long. To remove the
facing, loosen the screws, slide the facing
forward and pull the screws through the round
holes.
If you are making a rip type cut in material
thinner than 3/16 in. while the fence is
positioned over the depressed area of table
extension, the facing should be attached to the
fence so thatthe bottom edge touches the top
surface of the extension. In this case, the
facing must be shorter than the fence. This will
prevent thin material from sliding under the rip
fence.
WOOD FACING
8
MITER GAUGE.. head is locked in position
for crosscutting or mitering by tightening the
lock knob. ALWAYS LOCK IT SECURELY
WHEN IN USE.
There are slots for the stcp pin at the 45 deg tee
right and left positions for conveniently setting
the Miter Gauge to cut miters,
NOTE: The slots for the stop pin and the
graduations are manufactured to very close
tolerances which provide accuracy for average
woodworking. In some cases where extreme
accuracy is required, when making angle cuts,
for example, make a trial cut and then recheck
it.
If necessary, the miter gauge head can then be
swiveled slightly to compensate and then
locked.
Slots are provided in the miter gauge for
attaching an AUXILIARY FACING to make it
easier to cut long pieces. Be positive facing
does not interfere with the proper operation of
the sawblade guard.
Select a suitable piece of smooth straight
wood . . ari]l two holes and attach it with
screws.
NOTE: When bevel crosscutting, attach facing
so that it extends to the right of the miter gauge
and use the miter gauge in the groove to the
right of the blade.
LOCK
)LD DOWN
CLAMP
STOP PIN 45 ° SLOT
FOR STOP PIN
ARY
FACING
7 BLADEGUARD must always be in place and
work ng properly for all thru-sawing cuts. That
is, all cuts whereby the blade cuts compete y
through the workpiece.
To remove the guard for special operations,
loosen the wing nuts and slide the guard off of
the rod. DO NOT DISTURB THE SETTING OF
THE ROD.
When rep acing the guard, make sure the PIN
in the rod engages with the NOTCH n the
spreader support. Make sure wing screws are
tightened securely.
8 TABLE INSERT is removable for removing or
installing blades or other cutting tools.
_G: TO AVOID
INJURY
DUE TO
;H "OFF"
POWER
VING
surface.
ROUND HEAD /
#10 WOOD SCREWS
28
d pull toward
