ACCESSORIES
Windshield MZW 30
The foam-rubber-windshield
should be drawn over the sound
inlets of the microphone when
wind disturbances are evident.
Largest diameter: 60 mm
Length: 80 mm, Reduction of
wind disturbance: approx.20 dB.
Shock mount MZS 415
The shock mount can be con-
nected to all tripods, booms, etc.
with 3/8" threads and prevents
recordings being disturbed by
footfall or other strong mechanic-
al disturbances. Diameter: 35 mm.
Length: 80 mm.
Microphone clamp MZQ 415
The clamp can be fitted on tri-
pods, booms etc. with 3/8"
threads.
Battery adapters
Battery adapter MZA 15
Can be connected into the
microphone line at any point.
Fitted with 9 mercury cells
Mallory RM 625, it provides a
continuous operation for 50 to 60
hours. The mercury cells can be
purchased in allshopswithcater
for the hard of hearing. Special
feature: Ifthe plug and connector
are connected together the battery
condition is indicated by a built-in
LED. To prevent an unnecessary
discharge of the batteries, the
battery adapter should be
unscrewedfrom the microphone
when it is not in use.
Dimensions in mm: 220 x 132.
12
Power supplies
Swivel mount MZG 415
The swivel mount gives the
possibility to use the desk stand
together with the microphone
clamp or the shock mount for
the MKH 406 T
Power unit MZN 16 T and T-U
For simultaneous powering of
two microphones. Connection
to 220 volt or 110 volt supplies.
The unit can be included in the
microphone cable at any point.
Model T-U with Cannon
connectors.
Dimensions in mm:
168 x 120 x 50.
Cables
Connecting cable KA 1 and
KA 7
Tripie conductor screened cable.
Fitted with 3 pin connectors
according to DIN 41524.
KA 1: 1.5 m long,
KA 7: 7.5 m long
Connecting cable KAM 1-5
For the connection of series 6
microphones to the "Microport"
transmitters SK 1006, SK 1007,
SK 1008 and the SER 1. The
microphones are powered from
the transmitter.
KAM 1-5: 1 m long.
Connecting cable KA 7 U
For use with all Sennheiser micro-
phones with the sullix U. The
KA 7-U is fitted on one end with
a Cannon female connector,
and on the other end with a Cannon
plug (XLR-3-12 C).
Cable length: 7.5 m
13
Desk stand MZT 441
The MZT 441 is together with
the swivel mount MZG 415 and
the microphone clamp MZQ 415
or the shock mount MZS 415 a
stable desk stand for the
MKH 4061.
Auxiliary units
Transistor amplifier KAT 15-2
For the connection of condenser
microphones, or symmetrical
low impedance dynamic micro-
phon es, to the line and access-
ory inputs respectively, of the
Nagra 111or Nagra IV. Selected
functions:
T = condenser microphones
N = dynamic microphones
A switchable footfall filter is in-
cluded.
Dimensions in mm: 85x40x25.
Desk stand MZT 100
A stable desk stand with good
handling noise suppression. For
use with the MKH 406 T the
MZT 100 is to be combined with
the swivel mount MZG 415 and
the microphone clamp MZQ 415
or the shock mount MZS 415.
Roll-oft-filter MZF 15
The roll-oll-filter MZF 15 should
be included only between supply
voltage source and amplifier
input.
Frequency reduction
at 50 Hz approx. 6dB
at 25 Hz ~ 15 dB
Dimensions in mm: 220x152.
Battery adapter MZA 15-U
Same as MZA 15, however fitted
with Cannon connector XLR-3-11 C
and plug XLR-3-12 C for use with
the MKH-U types.
Dimensions in mm: 22 0 x 152.
