Filter
Top Products
ASUS P2-99 User’s Manual 13
III. HARDWARE SETUP
Motherboard Settings
1) AGPFS p. 14 AGP Bus Frequency Setting
2) KBPWR p. 15 Keyboard Power Up Setting (Disable/Enable)
3) VIO p. 15 I/O Voltage Setting (Normal/Test)
4) VCORE p. 16 Core Voltage Setting (Normal/Test)
5) FS0, FS1, FS2, FS3 p. 16 CPU External Clock (BUS) Frequency Selection
6) BF0, BF1, BF2, BF3 p. 17 CPU Core:BUS Frequency Multiple
Expansion Slots/Sockets
1) System Memory p. 18 System Memory Support
2) DIMM1, DIMM2 p. 19 DIMM Memory Module Support
3) Slot 1 p. 21 CPU Support
4) SLOT1, SLOT2, SLOT3 p. 26 16-bit ISA Bus Expansion Slots
*
5) PCI1,PCI2,PCI3,PCI4 p. 26 32-bit PCI Bus Expansion Slots
6) AGP p. 27 Accelerated Graphics Port
Hardware Monitor (optional)
1) JTPWR, JTCPU p. 25 Thermal Sensor Connectors
Connectors
1) PS2KBMS p. 28 PS/2 Mouse Port Connector (6 pin-female)
2) PS2KBMS p. 28 PS/2 Keyboard Port Connector (6-pin female)
3) PARALLEL p. 29 Parallel (Printer) Port Connector (25-pin female)
4) COM1, COM2 p. 29 Serial Port COM1 & COM2 (two 9-pin male)
5) USB p. 29 Universal Serial BUS Port Connectors 1 & 2 (Two 4-pin female)
6) Primary/Secondary IDE p. 30 Primary/Secondary IDE Connectors (Two 40-1 pins)
7) FLOPPY p. 30 Floppy Drive Port Connector (34 pins)
8) IDELED p. 31 IDE LED Activity Light (2 pins)
9) WOR p. 31 Wake-On-Ring Connector (2 pins)
10) CHA_, PWR_, CPU_FAN p. 32 Chassis, Power Supply, CPU Fan Power Lead (3 pins)
11) WOL_CON p. 33 Wake-On-LAN Connector (3 pins)
12) IR p. 33 Infrared Port Module Connector (5 pins)
13) SBLINK p. 34 SB-Link™ Port Connector (6-1 pins)
14) SMB CON. p. 34 SMBus Connector (3 pins)
15) ATXPWR p. 35 ATX Motherboard Power Connector (20 pins)
16) CHASIS p. 35 Chassis Intrusion Alarm Lead (4-1 pins)
17)
PWR.LED (
PANEL
)
p. 36 System Power LED Lead (3-1 pins)
18)
KEYLOCK (
PANEL
)
p. 36 Keyboard Lock Switch Lead (2 pins)
19) SPEAKER (PANEL) p. 36 System Warning Speaker Connector (4 pins)
20) MSG.LED (PANEL) p. 36 System Message LED (2 pins)
21) SMI (PANEL) p. 36 System Management Interrupt Lead (2 pins)
22) PWR.SW (PANEL) p. 36 ATX Power / Soft-Off Switch Lead (2 pins)
23) RESET (PANEL) p. 36 Reset Switch Lead (2 pins)
*
The optional onboard hardware monitor uses the address 290H-297H so legacy ISA cards
must not use this address otherwise conflicts will occur.
Layout Contents
III. H/W SETUP