Filter
Top Products
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
SC S
LENS SHIFT
+
–––
++
FOCUS ZOOM
I
N
T
E
R
I
NP
U
T
M
1-D
R
GB
B
N
G
S
-V
I
D
E
O
S
T
A
N
D
BY
/
O
N
T
E
M
P
V
ID
EO
C
O
M
P
O
N
E
N
T
L
A
M
P
K
E
Y
ST
O
N
E
S
E
A
R
C
H
R
E
S
E
T
M
E
N
U
F
OCUS
LE
N
S
S
H
I
FT
Z
O
O
M
V
I
D
E
O
R
-
A
U
D
IO
I
N
-
L
S-
V
I
D
E
O
BNC
R
G
B
A
U
D
I
O
I
N
1
A
U
D
I
O
I
N
2
R
GB O
U
T
A
U
D
I
O
O
U
T
REM
OT
E
CON
T
R
OL
R/C
R
/
P
R
G/Y
B
/
C
B
/
P
B
H
V
Y
C
ONT
ROL
NETWOR
K
CR/PR
C
a/Pa
I
N
T
E
R
I
N
P
U
T
M
1
-D
R
GB
B
N
G
S
-
V
I
D
E
O
ST
A
N
D
B
Y
/
O
N
T
E
M
P
V
I
D
E
O
C
O
M
P
O
N
E
N
T
L
A
M
P
K
E
YST
O
N
E
S
E
A
R
C
H
R
E
SE
T
M
E
N
U
F
O
CU
S
LE
N
S
S
H
I
F
T
Z
O
OM
V
I
D
E
O
R
-
A
U
D
I
O
I
N
-
L
S-V
ID
E
O
BNC
RGB
A
U
D
I
O
I
N
1
A
U
D
IO
I
N2
R
GB O
U
T
A
U
D
IO
O
U
T
REMOTE
CON
T
R
OL
R
/C
R
/
P
R
G/Y
B/
C
B
/
P
B
H
V
Y
CO
N
TROL
N
ET
WOR
K
CR/
PR
Ca/Pa
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
BLANKASPECT LASER
LENS SHIFT
+
–––
++
FOCUS ZOOM
IN
T
E
R
I
N
P
U
T
M
1
-
D
R
GB
BNG
S
-V
I
D
E
O
S
T
A
NDB
Y/
ON
T
E
M
P
V
ID
E
O
C
O
M
P
O
N
E
N
T
L
A
MP
KEY
S
T
ONE
SE
A
R
C
H
RES
E
T
M
E
N
U
F
O
C
US
LE
N
S S
H
IF
T
ZO
O
M
V
I
D
E
O
R
-
A
U
D
I
O
I
N
-
L
S
-
V
I
D
E
O
BNC
RG
B
A
U
D
I
O
I
N
1
A
U
D
I
O
I
N
2
R
G
B
O
U
T
A
U
D
I
O
O
U
T
R
E
M
O
TE
C
ON
T
R
O
L
R
/C
R
/
P
R
G
/
Y
B
/
C
B
/
P
B
H
V
Y
CO
N
TR
OL
N
ET
W
O
RK
CR/
P
R
C
a
/Pa
15
Turning On The Power
WARNING • When the power is ON, a strong light is emitted. Do not look
into the lens or vents of the projector.
• Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.
NOTE
Power ON/OFF
Power ON/OFF
Remove the lens cap.
2
Set the power switch to [ | ] (ON).
The STANDBY/ON indicator will light to solid orange.
STANDBY/ON
STANDBY/ON button / indicator
LENS SHIFT
buttons
Power switch (ON position)
STANDBY/ON
button
STANDBY/ON
3
Press the STANDBY/ON button.
The projector lamp will light up and the
STANDBY/ON indicator will begin blinking green.
When the power is completely on, the indicator
will stop blinking and light green.
4
Use the LENS SHIFT buttons to shift the
picture upward or downward.
5
Select an input signal according to the
section “Selecting An Input Signal” of the
following page.
LENS SHIFT
Power switch (OFF position)
1
Press the STANDBY/ON button.
The message “Power off?” will appear on
the screen for approximately 5 seconds.
Attached the lens cap.
2
Press the STANDBY/ON button again while
“Power off?” the message is visible.
The projector lamp will go off, and the
STANDBY/ON indicator will begin blanking orange.
Then the STANDBY/ON indicator will stop blinking
and light to solid orange when the lamp cooling is
complete.
3
Switch the power switch to [O] (OFF).
The STANDBY/ON indicator will go off.
STANDBY/ON
button
STANDBY/ON
STANDBY/ON
STANDBY/ON button / indicator
Turning Off The Power
STANDBY/ON
VIDEO
LASER INDICATOR
RGB
BLANKASPECT LASER
LENS SHIFT
+
–––
++
FOCUS ZOOM
1
4