Filter
Top Products
Handheld Type
Advanced Marker Settings
The handheld type LUMA monitors can display various area
markers, including a center marker and aspect markers.
The brightness of these markers can be selected from three
different levels, white, gray, and dark gray, and their widths
can be selected from FINE, STANDARD, and BOLD. Users can
also select either a black or gray matte to fill the outer area of
the aspect markers. These flexible marker controls, together
with the choice of many different aspect markers, make the
handheld type LUMA monitors extremely convenient for a
variety of shooting scenarios.
Color Temperature/Gamma Selection
High/low color temperatures or user preset can be selected.
A variety of gamma modes can also be selected.
Three-color Tally
All handheld type LUMA monitors come equipped with a tally
lamp that can be lit up via a parallel remote connector.
The status of the signal displayed on the monitor can be
identified by the tally color – red, green, or amber.
Parallel Remote Control
The handheld type LUMA monitors can be controlled remotely
via their parallel remote connectors. There are 27 functions in
the remote menu (such as the ability to switch input signals),
of which seven can be allocated to the connector.
Monaural Audio Monitoring
All handheld type LUMA monitors are equipped with a speaker
(0.5 W), which enables the user to monitor audio.
Protected Controls
The key-inhibit function helps prevent inadvertent operations
from the control panel.
Convenient Installation
As with all other LUMA monitors, handheld type LUMA
monitors eliminate the many concerns inherent in CRT
monitors, including convergence misalignments, geometric
distortion, flicker, image burn-in, and the effect of magnetic
fields.
Mounting Flexibility
The handheld type LUMA monitors are 5U high and half-rack
wide. Using the optional MB-525 Mounting Bracket with a nine-
step tilt capability, two units can be installed side-by-side in a 19-
inch EIA standard rack.
Other Features
• Setup Level for Analog Component and NTSC signal
• Sub Control on Contrast, Chroma, Phase, and Brightness
• Blue-only mode
• Power-saving Function
• Monochrome mode
• 4:3 Zoom
11
Wide Viewing Angle
The LCD panels used in the handheld type LUMA monitors
have a wide viewing angle of 170 degrees, both horizontally
and vertically, with minimal reduction in picture contrast.
AR (anti-reflection) Coated Protection Panel
The handheld type LUMA monitors use robust AR-coated
protection layers, which minimize the chance of their panels
being scratched during transportation – an extremely important
criteria for use in the field or in any mobile application. The AR
coating additionally has two unique characteristics: it provides a
high transmission rate of the internal light source to keep the
picture as bright as possible, and it keeps reflection from
ambient light to a minimum. As a result, when used in bright
lighting conditions, high contrast is still maintained even in dark
areas of the picture.
Operational Convenience
ENG Kit VF-509
The handheld type LUMA monitors are a strategic choice for
use in ENG and EFP field operations. When compared to CRT
displays, the picture contrast of these monitors is affected less
by ambient light, allowing clear images to be viewed even
under strong sunlight. For further protection, the optional
VF-509 ENG kit provides a Viewing Hood, Carrying Handle,
and Connector Protector.
4:3/16:9 Switchable Display
The scan aspect ratio can be switched between 4:3 and 16:9.
Selectable Scan Size
The scan size can be selected between 5% over-scan, 0%,
and -3% underscan modes.
16:9 Mode 4:3 Mode
Aspect Marker 4:3, 15:9, 14:9, 13:9, 16:9
1.85:1, 2.35:1, 1.85:1& 4:3
Center Marker O
Connector Panel for LMD-9050, LMD-9030 and LMD-9020
MK10231V1_p04_13.qxd 06.1.16 8:06 PM Page 11