Extron electronic TLP 710MV Projector User Manual


  Open as PDF
of 4
 
3
Product Category
Initial Conguration
Before use, configure the touchpanel, using the on-screen menus.
1. Press the Menu button once. (See “Menu button” under “TLP 710MV Reset Buttons and LED“ for the TLP 710MV or
“Rear Panel Features“ for the TLP 710TV.) The Main menu screen opens (see figure at right).
2. Press an on-screen button to highlight and select an option (the button turns green with a yellow border).
3. Use the Up and Down buttons to adjust the value. Some options have a single button and toggle between Off and On
when the button is pressed.
There are five different screens (Main, Volume, Time, Network, and Video) that
can be selected by pressing the appropriate button at the left side of the
screen. There is also an Exit button at the bottom left corner of the screen for
saving changes and leaving the menus.
Use the screens to adjust the following options (for more information, see the
TLP 710MV and TLP 710TV User Guide).
Main — adjusts the Sleep timer, Backlight, Auto Backlight, and Wake on
Motion functions. The screen also provides information about the PoE status.
Volume — adjusts the Master, Click, Sounds, and Line In volume settings.
Time — sets the correct time and date.
Network — sets the IP address and the subnet mask, and enables or disables Dynamic Host Configuration Protocol.
Video — provides a small video preview window and the controls to adjust the video contrast, color, brightness, and tint.
Calibration Menu
1. Press the Menu button a second time to open the calibration-screen (see
“TLP 710MV Reset Buttons and LED“ for the TLP 710MV or “Rear Panel
Features“ for the TLP 710TV). The on-screen button in the top left corner is
highlighted.
2. Press and hold the highlighted button until it turns gray and a new button
is highlighted. Repeat until all four points have been calibrated. The screen
reopens to the Main Screen.
3. Press Exit to close the on-screen menus.
4. (TLP 710MV) if necessary, reattach the faceplate.
Mounting Options
TLP 710MV
z Wall mounting — using the Extron BB 710M back box (part number 70-971-01) or the Extron EWB 710 wall box (part
numbers 70-969-02 [black] or 70-969-03 [white]), any of which must be purchased separately. Follow the instructions
provided with the kit. The unit may also be mounted directly to the wall without a kit, as described on page 4.
z Furniture mounting — as described on page 4.
z Rack mounting — using the RM 710M kit (part number 70-970-01), which must be purchased separately. Follow the
instructions in the user guide provided with the kit.
TLP 710TV
z Desktop mounting — by standing the unit on a suitable surface. For added security, the unit may be attached to the
desktop, using two screws, as described in the TLP 710MV and TLP 710TV User Guide.
The TLP 710TV can also be mounted using the Extron SMA-1 Swivel-Mount Adapter (part number 70-747-01), which
must be purchased separately. Follow the instructions provided with the kit and the TLP 710MV and TLP 710TV User
Guide.
z VESA mounting — using the D-type (75 x 75 mm) mounting pattern. The Extron LPVM-1 kit (part number 60-1099-02)
is optional and must be purchased separately. Follow the instructions provided with the kit. To VESA-mount the
TLP 710TV, the base must be removed from the unit, as described in the TLP 710MV and TLP 710TV User Guide.
Main
Volume
Time
Network
Video
Exit
On
On
Down Up
Sleep timer: 300 Sec
Down Up
Backlight: 073%
Auto Backlight
Wake on Motion
PoE
Active
+
+
++
Press and Hold
Highlighted Box
Until Color Changes
 previous