Filter
Top Products
4. To punch, press the PUNCH ~ button (D2). The
DocuBind TL300 punches up to 12 sheets of 20 Ib./80
gram paper at once. Punch only TWO clear covers at a
time to prevent jams and excessive wear.
5. If punch jams, de~s the RESET[Z]button (D3). Then
press the PUNCH~button (D2) again and remove paper
or covers from punch throat (it may be necessary to punch
several times in order to remove the paper). Repeat steps 1
to 4 with slightly less paper to avoid punch jams on addi-
tionallifts.
E. BINDING
1. Using the dial on the left side adjust the Wire Crimper to
correspond with the wire element size to be used.
2. Place the large loops of the wire element into the Wire
Holder as shown in figure 3. Be sure it is firmly secured
with the small loops facing toward you.
3. Place your punched pages face downward onto the small
loops of the wire element. Then place your front and back
covers face-to-face against each other. Place the covers
onto the wire element with the back cover first and the
inside of the front cover facing upward. This step ensures
that after crimping the seam of the wire element will be
hidden between the back cover and last page (figure 4).
4. Hold the wire element firmly at each end of the book and
remove it from the Wire Holder by sliding it to the left or
lifting it off. While firmly holding the wire element at each
end place the book with the open end of the wire face
down into the Wire Crimper. You can release the book
so it rests against the suppOr1 rack or continue to hold it
with one hand (figure 5).
5. To crimp the wire together pull the handle down toward
you completely until it goes no fur1her. Remove the book
and flip the front cover around to the front. Your
presentation is now complete.
F. EMPTY CHIP DRAWER
1 Empty Chip Drawer (F) after repeated use. Pull drawer
gently toward you to open. When putting back in, the
drawer will snap into place (see figure 6).
G. SERVICE
Should your DocuBind require service contact
Quar1et, a GBC Company
5700 Old Orchard Road
Skokie, IL 60077 USA
1-800-541-0094
http.llwww.quar1etgbccom
Thank you for purchasing fhe GBC OocuBind TL300. This sys-
tem features our new exctusive wire hotder design that
enables you to assemble your document as you punch, making
it easier to load paper onto the binding comb than previous
systems! The OocuBind TL300 advanced punching technology
also makes it easier to punch more paper at once whife
providing grealer reliabifily.
A. GEmNG STARTED
1 Push the handle (A) onto the shaft located on the right side
of the machine (see figure 1), Align the flat spot of the
handle with the flat of the shaft and secure it with the allen
wrench provided.
2. Insert U shaped wire support bracket into holes on top rear
of machine.
3. Firmly push the female end of the power cord into the
power cord receptacle (A 1) located on the back of the
machine.
A CAUTION: Make sure this step is complete prior to
..plugging the male end of the power cord into a power
receptacle.
4 Plug the male end of the power cord into an appropriate
power receptacle
B. DETERMINE SHEET WIDTH
1. Set Edge Guide (B) to paper size you wish to bind (11",
8-1/2" letter size, 11-1/4" oversized cover, A4 ring, A5.
Japan A4) (see figure 1 ). When using oversized covers, set
the Edge Guide on Covers. punch all of the covers for your
job and set aside. Move the Edge Guide back to the 11"
selling to punch your contents then bind.
C. DmRMINE WIRE SIZE
1. Slide the Binder Sizer open (C) (see figure 1).
2. Place document including covers behind Binder Sizer.
3. Release the Binder Sizer and select the wire binding
element that corresponds with the size shown by guide.
For best results. always use GBC brand covers with GBC
color-coordinated wire
D. PUNCHING PAPER (see fIgure 2)
1. Lift the Paper Support (0) into place (optional).
2. Align sheets or covers and insert edge to be bound into
punch throat (01 ).
3. Jog the sheets until they are flush against the edge guide
and the bottom of the punch throat. Allow the paper to rest
against the Paper Support, or, you may prefer to hold the
sheets in place with one hand.
SPECIFICATIONS
Dimensions
Punch Capacity
Bind Capacity"
Maximum Sheet Width"
Dis-engagable Punch Pins:
Weig~t:
Electrical Power:
18. (W)x81/2. (H)x16. (0)
457mm x 216mm x 406mm
351bs. (15.5 kg.)
115V AC, 60Hz, 4.3 amps, 130
watts or 230V AC, 50Hz,
1.3 amps
3
12 sheets of 20 Ib paper
12 sheets of 80gm2 paper
125 sheets or 9116"
(14mm)
11.7"(297mmA4)
1 (A5 paper)
within wire storage bin