GBC TL300 Binding Machine User Manual


 
SAFETY MESSAGES
Your safety as well as the safety of others is important to
GBC. In this Operator Manual and on the product are impor-
tant safety messages. Read these messages carefully.
A The safety alert symbol precedes each safety message
..in this Operator Manual. This symbol indicates a
potential personal safety hazard that could hurt you or oth-
ers. as well as cause product or property damage.
The following warning is found on this unit:
This safety message means you could be seriously hurt or
killed if you open the product and expose yourself to haz-
ardous voltage.
h CAUTION: IN CASE OF EMERGENCY, USE THE POWER
..CORD AS A MAIN DISCONNECT DEVICE!
.Unplug the DocuBind TL30O before moving it, or when it is
not in use for an extended period of time.
.Do not operate with a damaged supply cord or plug, after it
malfunctions, or after it has been damaged in any manner.
.Do not overload eiectrical cutlets beyond their capacity as
this can result in fire or electrical shock.
.Do not alter attachment plug. Plug is configured for the
appropriate electrical supply.
.The unit is intended for indoor use only.
.Never push objects into this product through cabinet slots.
Do not spill liquid of any kind on this product
.Do not operate if the product has been exposed to rain or
water.
SERVICE
Do not attempt to service or repair the DocuBind TL300
yourself. Unplug the unit and contact an authorized GBC ser-
vice representative for exchange or repair.
CLEANING
A CAUTION: Unplug this product before cleaning.
Wipe exterior only with a damp Cloth Do not use detergents
or solvents.
The following notes apply only to the units rated 230V 50Hz.
MAIN CORDSET SELECTIDN (FOR 230VAC MACHINES ONLY)
When choosing a detachable line cord for use with the
DocuBind TL300, always observe the following
The cordset consists of three Components; the attachment
plug, cordage and appliance inlet. Each of these Components
must meet European regulatory approvals for safety.
The following minimum electrical ratings for the specific
cordset are published for safety purpoSeS. DO NOT USE
CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM
ELECTRICAL REQUIREMENTS.
PLUG: 3A, 250 volts, 50/60 Hz, Class 1,3 conductor,
European safety agency approved.
CORDAGE: Type H05W-F3GO.75, Harmonized ( <I HAR t> ).
The "<I t>" symbols indicate cordage approved to appro-
priate European standard (NOTE. "HAR" may be substituted
by the approval mark of the European safety agency which
approved the cordage. An example would be" <I V DE t>".
APPLIANCE CONNECTOR: 3A, 250 volts, 50/60 Hz, European
safety approved, Type IEC 320. Cordset shall not exceed 3
meters in length. Cordset with Component electrical ratings
greater than the minimum specified electrical ratings may be
substituted.
-
Q UARTETI8)
.A aecCOMPANY
SKOKIE, IL 60077
httpJ/www.quartetgbc.com
The following symbols appear on this product, and their
meaning is as follows
~PUNCH
~RESET
~ WARNING: For your protection, do not connect the
..DocuBind TL300 to electrical power until you read
these instructions completely. Keep these instructions in a
convenient location for future reference. To guard against
injury, the following basic safety precautions must be
observed in the set-up and use of this product.
IMPORTANTSAFEGUARDS
GENERALSAFEGUARDS
.Use the DocuBind TL300 only for its intended purpose of
punching and binding paper and covers according to the
indicated specifications
.Do not place anything in the punch opening of the machine
other than paper and cover stock.
.Place unit on a secure, stable work area to prevent the
machine falling and possibly causing personal injury and
damage to the unit.
.Follow all warnings and instructions marked on the product.
.Lift the machine from the bottom, not the cover
.Do not lift the machine by the cover or paper holder wire.
ELECTRICAL SAFEGUARDS
The DocuBind TL300 must be connected to a supply voltage
corresponding to the electrical rating of the machine as indi-
cated on the serial/rating plate or in this manual.
""' CAUTION: THE POWER RECEPTACLE MUST BE LOCATED
..NEAR THE EQUIPMENT AND BE EASILY ACCESSIBLE.