Filter
Top Products
1413
16
15
LOST COMMUNICATION
If the main unit display line for the remote sensor
reading goes blank, press and hold DOWN ( ) button
for 2 seconds to begin a new signal search. If the signal
still isn’t received, make sure that remote sensor is in
its proper location:
• The distance between main unit and remote sensor is
not over 100 feet (30meters).
• The path between units is clear of obstacles. Reduce
the distance as necessary.
• Fresh batteries are installed correctly in both units.
If there is no reception, please perform the following steps:
• Bring the main unit and remote sensor close together.
• Remove four (4) small screws from the back of the
remote sensor with small Phillips screwdriver, and
open the battery compartment.
• Remove the batteries from the battery compartment
and reinstall them in the same manner. Remote
sensor LED indicator will flash showing transmission
of the signal.
• Remove the batteries from the main unit and reinstall
them in the same manner.
• The remote temperature appeared on the main unit’s
display will show that transmission is being received
successfully.
CALENDAR AND CLOCK DISPLAY MODES
Date is displayed in month-date or date-month format.
Each press of the MODE button will change the clock
display setting between the time of day with seconds,
time of day with the day of the week and a calendar.
MANUAL SETTINGS
CLOCK
• Press and hold MODE button for 3 seconds: the year
digits will flash.
• Press UP ( ) or DOWN ( ) to change flashing digits.
• After the first value is set, press MODE button again
to confirm.
• Continue setting month, date, time display format, 12
or 24 hour time format, hour, minute, day of the week
display language, time zone and Fahrenheit or Celsius
display.
• Press MODE for the last time to return to the default
mode (time of day with seconds) after the last
parameter is set.
ALARMS
(W) Weekly Alarm
The alarm will sound and the alarm icon will flash at
the set time Mondays through Fridays.
(S) Single Day Alarm
The alarm will sound and the alarm icon will flash at
the set time, but will not activate on subsequent days.
(PRE-AL) Low Temperature Pre-Alarm for remote location
If the remote temperature reaches 32ºF (0ºC) or below,
the pre-alarm feature will be activated. The pre-alarm
time interval can be set for 15, 30, 45, 60 or 90 minutes
earlier than the day of the week or single alarm time.
Press and hold ALARM button for two seconds in Pre-
Alarm mode to set the pre-alarm interval.
W (Weekly alarm), S (Single day alarm), and PRE-AL
(Pre-alarm) icons will indicate which alarm mode is
armed. You can enable or disable an alarm by pressing
the UP ( ) or DOWN ( ) buttons in the selected alarm
display mode. Press ALARM button to toggle between
alarm modes or to return to the default display.
PRECAUTIONS
This product is engineered to give you years of
satisfactory service if handled carefully. Here are a few
precautions:
• Do not immerse the units in water.
• Do not clean the units with abrasive or corrosive
materials. They may scratch the plastic parts and
corrode the electronic circuits.
• Do not subject the product to excessive force, shock,
dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries,
and damaged parts.
• Do not tamper with the units internal components.
Doing so will invalidate the warranty and may cause
damage. These units contain no user-serviceable parts.
• Use only fresh batteries. Do not mix new and old
batteries.
• Read the user's manual thoroughly before operating
the units.
TRANSMISSION COLLISION
Signals from the other household devices such as
wireless doorbells, home security systems, and entry
control, may interfere with this product or cause
temporary reception interruption. This is normal and
will not affect the general performance of the product.
The transmission and reception of the temperature
readings will resume once the interference subsides.
SETTING THE ALARM
To set any alarm,
• Press ALARM button once to display alarm time. If
the alarm is off, OFF will be displayed.
• Press and hold ALARM button for two seconds. The
hour digit will flash.
• Enter the hour using DOWN ( ) or UP ( ).
• Press ALARM button again. The minute digits will
flash.
• Enter the minutes using DOWN ( ) or UP ( ).
• Press ALARM button again to exit.
• Repeat the same procedure to set a Single and Pre-
Alarm.
SNOOZE
When the alarm sounds, press the SNOOZE button to
temporarily stop the alarm. After the SNOOZE is
depressed, the alarm sound will resume in five (5)
minutes. If the alarm is not disabled after that, it will
sound for four (4) more minutes and then will stop by
itself.
DISABLING ALARM
Press ALARM button on the main unit to disable any
of the alarms. When Weekly, Daily or Pre-Alarm is
disabled, an applicable icon W, S, or Pre-Al will
disappear from the main unit’s display.