Kingston Technology KNE16TP/RS Switch User Manual


  Open as PDF
of 30
 
Hardware Installation 9
KNE24TP/RS User’s Guide - Rev. A01 Kingston Technology Company
Stacking EtheRx Hubs
The EtheRx hubs use stacking ports located on the rear panel to stack up to five
hubs in any combination of 16-Port KNE16TP/RS and 24-Port KNE24TP/RS
models. Follow the directions below to stack up to five hubs together:
1. Locate the 5.5” shielded stacking cable included with your package
contents.
2. Plug one end of the cable into the port labeled, “Stack-Out” on the
first hub.
3. Plug the other end of the cable into the “Stack-In” port on the second
hub.
4. Connect the AC power cord to each hub, then flip the power switch
to turn on power to the unit.
5. Repeat the process to stack additional hubs up to a maximum of five
(5) hubs.
Kingston’s Stack-n-Play
™
feature offers greater scalabilty to add UTP ports
without the need to configure ID or termination switches. EtheRx hubs when
stacked together are recognized as a single repeater unit on the network. By
stacking hubs together, you can expand the total number of UTP port
connections from 16 to 80 or from 24 to 120 UTP ports, depending on the
model. A maximum of five (5) Pro-Series hubs can be stacked in any
combination of 16 and 24-Port hub models.
Kingston’s Hot-Stack
™
feature allows the addition of new hubs to the top or
bottom of a stack without the need to power down the existing hubs.
STACK-IN
STACK-OUT
AUI
OFF
ON
100-240VAC 50-60HZ 1A
EXTERNAL TRANSCEIVER
( SQE JUMPER DISABLED)
UTILIZATION % - Bar graph indication
(in percentage) of the traffic rate in
reference to the 10 Mbps Ethernet
bandwidth.
COLL %
UTIL %
1%
7%
15%
30%
60%
1%
7%
15%
30%
60%
Green
Green
Green
Amber
Orange
Amber
Amber
Amber
Amber
Red
COLLISION % - Bargraph indication
(in percentage) of the packet collision
rate in the network.
PORT #16 OR PORT #24
CASCADE CONFIGURATION
For cascading to another MDI-X
hub port using straight-thru cable.
For connection to workstation NIC
using cross-over cable.
For cascading to another MDI-X
hub port using cross-over cable.
For connection to workstation NIC
using straight-thru cable.
BNC
STACK-IN
STACK-OUT
AUI
OFF
ON
100-240VAC 50-60HZ 1A
EXTERNAL TRANSCEIVER
( SQE JUMPER DISABLED)
UTILIZATION % - Bar graph indication
(in percentage) of the traffic rate in
reference to the 10 Mbps Ethernet
bandwidth.
COLL %
UTIL %
1%
7%
15%
30%
60%
1%
7%
15%
30%
60%
Green
Green
Green
Amber
Orange
Amber
Amber
Amber
Amber
Red
COLLISION % - Bargraph indication
(in percentage) of the packet collision
rate in the network.
PORT #16 OR PORT #24
CASCADE CONFIGURATION
For cascading to another MDI-X
hub port using straight-thru cable.
For connection to workstation NIC
using cross-over cable.
For cascading to another MDI-X
hub port using cross-over cable.
For connection to workstation NIC
using straight-thru cable.
BNC
STACK-IN
STACK-OUT
AUI
OFF
ON
100-240VAC 50-60HZ 1A
EXTERNAL TRANSCEIVER
( SQE JUMPER DISABLED)
UTILIZATION % - Bar graph indication
(in percentage) of the traffic rate in
reference to the 10 Mbps Ethernet
bandwidth.
COLL %
UTIL %
1%
7%
15%
30%
60%
1%
7%
15%
30%
60%
Green
Green
Green
Amber
Orange
Amber
Amber
Amber
Amber
Red
COLLISION % - Bargraph indication
(in percentage) of the packet collision
rate in the network.
PORT #16 OR PORT #24
CASCADE CONFIGURATION
For cascading to another MDI-X
hub port using straight-thru cable.
For connection to workstation NIC
using cross-over cable.
For cascading to another MDI-X
hub port using cross-over cable.
For connection to workstation NIC
using straight-thru cable.
BNC
STACK-IN
STACK-OUT
AUI
OFF
ON
100-240VAC 50-60HZ 1A
EXTERNAL TRANSCEIVER
( SQE JUMPER DISABLED)
UTILIZATION % - Bar graph indication
(in percentage) of the traffic rate in
reference to the 10 Mbps Ethernet
bandwidth.
COLL %
UTIL %
1%
7%
15%
30%
60%
1%
7%
15%
30%
60%
Green
Green
Green
Amber
Orange
Amber
Amber
Amber
Amber
Red
COLLISION % - Bargraph indication
(in percentage) of the packet collision
rate in the network.
PORT #16 OR PORT #24
CASCADE CONFIGURATION
For cascading to another MDI-X
hub port using straight-thru cable.
For connection to workstation NIC
using cross-over cable.
For cascading to another MDI-X
hub port using cross-over cable.
For connection to workstation NIC
using straight-thru cable.
BNC
STACK-IN
STACK-OUT
AUI
OFF
ON
100-240VAC 50-60HZ 1A
EXTERNAL TRANSCEIVER
( SQE JUMPER DISABLED)
UTILIZATION % - Bar graph indication
(in percentage) of the traffic rate in
reference to the 10 Mbps Ethernet
bandwidth.
COLL %
UTIL %
1%
7%
15%
30%
60%
1%
7%
15%
30%
60%
Green
Green
Green
Amber
Orange
Amber
Amber
Amber
Amber
Red
COLLISION % - Bargraph indication
(in percentage) of the packet collision
rate in the network.
PORT #16 OR PORT #24
CASCADE CONFIGURATION
For cascading to another MDI-X
hub port using straight-thru cable.
For connection to workstation NIC
using cross-over cable.
For cascading to another MDI-X
hub port using cross-over cable.
For connection to workstation NIC
using straight-thru cable.
BNC
STACK-IN
STACK-OUT
PORT #16 OR P
CASCADE CONFIG
For cascading to
hub port using s
For connection t
using cross-ove
For cascading to
hub port using c
For connection t
using straight-th
STACK-IN
STACK-OUT
PORT #16 OR P
CASCADE CONFIG
For cascading to
hub port using s
For connection t
using cross-ove
For cascading to
hub port using c
For connection t
using straight-th
STACK-IN
STACK-OUT
PORT #16 OR P
CASCADE CONFIG
For cascading to
hub port using s
For connection t
using cross-ove
For cascading to
hub port using c
For connection t
using straight-th
Stack
up to
5 hubs
maximum
Fig. 3. Stacking Additional Hubs
 previous next