Filter
Top Products
5
features and specifications
Adjustable Bass Boost
Frequency
Adjustable Bass Boost
Adjustable Q Control
Selectable Crossover
Frequency
-High Pass
-Mid High Pass
-Mid Low Pass
-Subwoofer (Low Pass)
Power Supply
Input Impedance
S/N ratio
Slope Rate
Max Output Signal Level
Channel Separation
Distortion
Dimensions,WxDxH,inches
(millimeters)
25Hz-250Hz
0-18dB
2-20
40Hz-8KHz
40Hz-800Hz
2KHz-7KHz
40Hz-400Hz
10-16V DC, negative ground
10K Ohm
more than 85dB
12dB/Octave
7.0V/RMS
60dB
less than 0.05%
6x12-11/16x1-3/4
(150 x 322 x 45)
1. BASS BOOST CONTROL
2. BASS BOOST LEVEL CONTROL
3. SUBWOOFER MODE SWITCH
4. VARIABLE SUBWOOFER FREQUENCY
CONTROL 40Hz-400Hz
5. PARAMETER "Q" CONTROL 2-20
6. VARIABLE SUBWOOFER BASS BOOST
FREQUENCY CONTROL 25Hz-250Hz
7. SUBWOOFER STEREO/MONO MODE
CONTROL
8. SUBWOOFER OUTPUT LEVEL CONTROL
9. VARIABLE HIGH-PASS (MID-RANGE)
FREQUENCY CONTROL 40-800Hz
10. VARIABLE LOW-PASS (MID-RANGE)
FREQUENCY CONTROL 2KHz-7KHz
11. BAND PASS/HIGH PASS SELECTOR
12. LEFT AND RIGHT HIGH & LOW PASS
PHASE SHIFT CONTROL 0-180
13. MID-RANGE OUTPUT LEVEL CONTROL
14. VARIABLE HIGH-PASS FREQUENCY
CONTROL 40-8KHz
15. FREQUENCY MULTIPLIER (x1/x10 HIGH-
PASS CROSSOVER)
16. HIGH-PASS OUTPUT LEVEL CONTROL
17. SUBWOOFER INPUT PORT
18. MID/HIGH INPUT PORT
19. SUBWOOFER OUTPUT PORT
20. MID OUTPUT PORT
21. HIGH PASS OUTPUT PORT
22. REMOTE CONTROL JACK
23. POWER TERMINALS
This control adjusts the bass boost gain (0 to +18dB).
This control sets the subwoofer gain control.
Allows subwoofer mode channel to receive signal from either the mix of from low-pass inputs
directly (when head unit has appropriate 5ch/6ch outputs).
By turning the selector you can choose the subwoofer crossover points from 40Hz-400Hz.
Allows independent continuous change of the boost frequency bandwidth (Q-factor) for each band
from Q=20 (Narrow bandwidth, steep slope) to Q=2 (Wide bandwidth, gentle slope).
By turning the selector you can choose the subwoofer crossover bass boost points from 25Hz-
250Hz.
For selection of stereo or mono mode subwoofer output.
For adjusting the subwoofer channel output level.
By turning the selector you can choose the high-pass crossover points from 40Hz-800Hz.
By turning the selector you can choose the low-pass crossover points from 2KHz-7KHz.
When this switch is in high pass mode, the low pass filter cannot be used. It can convert rear
channel to band pass in tri amp system.
Allows you to change the phase of your high and low crossover from 0 to 180 degrees to help
compensate for timing difference between drivers.
For adjusting the mid-range channel output level.
By turning the selector you can choose the high-pass crossover points from 40Hz-800Hz.
This switch changes crossover points from 40Hz-800Hz to 400Hz-8KHz for high frequency high
channel drivers.
For adjusting the high pass channel output level.
To be connected to the subwoofer outputs of the source unit.
To be connected to the outputs of the source unit.
To be connected to the subwoofer channel amplifier left/right inputs.
To be connected to the rear channel amplifier left/right inputs.
To be connected to the front channel amplifier left/right inputs.
Plug the modular telephone style cord connected to the remote control unit into this jack.
Use these connectors to deliver power, ground, and remote turn-on control to the unit.
REMOTE CONTROL UNIT
1.BASS BOOST
This control sets the Bass Boost Gain from 0 to +18dB.
2.BASS LEVEL
This control sets the subwoofer level control.