Filter
Top Products
EN – 23
ENGLISH
The lamp is designed to project the image on the LCD
panels. When the lamp no longer functions, replace it
with a new one.
Caution:
• Do not remove the lamp immediately after using
the projector, you may get burned because of the
high temperature of the lamp.
• When you replace the lamp, press the power button
to power off, then wait for 120 seconds in stand-by
mode to allow the lamp and LCD panels to cool. Turn
off the main switch, unplug the power cord from
the outlet, and wait one hour so that the lamp is
cooled to the touch.
• Do not remove the lamp except for replacement.
Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may break
and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the pro-
jector. Also be sure not to insert metal or any flam-
mable objects, it may cause fire or electric shock. If
any objects are inserted, please unplug and contact
your dealer.
• Install the lamp securely, failure may cause a fire.
1. Reverse the projector gently.
2. Loosen the screws of the lamp lid
(a) using a phillips screwdriver (+).
3. Remove the lamp cover in the
direction of the arrow as indi-
cated.
4. Loosen screws (b) using a phillips
screwdriver (+), and remove them.
5. Pull up the handle.
6. Hold onto the projector by the
handle as you pull out the lamp.
Once the lamp has been removed,
do not spill liquid on it, place it near
flammable objects or where chil-
dren can touch it. Otherwise, it will cause injury or
fire.
7. Insert the new lamp securely into the projector body
in the right direction.
8. Put the handle back to the holding point.
• Make sure that the handle is locked.
9. Tighten up the screws (b) using a phillips screw-
driver (+).
10.
Tighten up the screws of the lamp lid using a phillips
screwdriver (+).
How to reset the operation time meter
Plug in the power cord, switch on the projector, and
reset lamp time by pressing the $, % and POWER
buttons simultaneously.
Important:
• If the 3 buttons was not pressed at the same time,
the lamp time may not be reset.
• Please confirm the TEMP indicator illuminates
about 2 seconds and the lamp time has been
reset.
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after you
replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.
Caution:
• Do not spill liquid on the lamp or place it near flam-
mable objects or where children can touch it. Oth-
erwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
Interval of the lamp replacement
The interval of the lamp replacement about 1,500 hours
of consecutive use. Replacement span may differ ac-
cording to operating environment, and may be shorter
than 1,500 hours. Decreases in luminescence and/or
color brightness will indicate that the light source lamp
needs to be replaced. When lamp operation time ex-
ceeds 1,000 hours, the indicator will flash alternately
between green and red (while the lamp is in operation;
when the lamp is not in operation, the indicator will
appear red only). When the lamp has been used for
about 1,400 hours, the message “LAMP!!.” will appear
on the screen for one minute. When the lamp has been
used for about 1,500 hours, the projector will automati-
cally shut off for safety and the power indicator light
will be red. The projector cannot be used until the lamp
has been replaced and operation timer has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut
yourself with glass fragments.
• The replacement span of the lamp depends on the
environment. For replacement lamps, please con-
tact your dealer.
The projector automatically shuts off when the
lamp is used up in about 1,500 hours and cannot
be used until the lamp is replaced and the
internal timer is reset.
(a)
Lamp replacement
(b)