Panasonic PT-VW435NE Projector User Manual


 
-5-
Specifications
Model No. PT-VW435NU / E / EA PT-VX505NU / E / EA
Power supply
AC100 V - 240 V 50 Hz/60 Hz
Power consumption
100 V - 240 V 4.0 A-1.6 A 365 W
When [Standby mode] of [Setting] is set to [ECO]: 0.3 W
When [Standby mode] of [Setting] is set to [Network]: 12.9 W or less
When [Standby MIC out] of [Sound] is set to [On]: Max.26 W
LCD panel
Panel size
1.5 cm(0.59")
(aspect ratio 16 : 10)
1.6 cm(0.63")
(aspect ratio 4 : 3)
Display method
3 transparent LCD panels (RGB)
Drive method
Active matrix method
Pixels
1 024 000
(1 280 x 800) x 3 panels
786 432
(1 024 x 768) x 3 panels
Lens
Manual zoom (1.6x) / Manual focus / Lens shift
F 1.6 to 2.12, f 15.28 mm to 24.62 mm
Luminous lamp
280 W UHM lamp
Light output *
1
4 300 lm 5 000 lm
Applica-
ble scan-
ning fre-
quency *
3
for RGB signal
Horizontal 15 kHz to 100 kHz, Vertical 50 Hz to 100 Hz
Dot clock frequency: 140 MHz or less
for YP
B
P
R
signal
[525i(480i)] Horizontal 15.75 kHz, Vertical 60 Hz
[525p(480p)] Horizontal 31.5 kHz, Vertical 60 Hz
[750(720)/60p] Horizontal 45 kHz, Vertical 60 Hz
[1 125(1080)/60i] Horizontal 33.75 kHz, Vertical 60 Hz
[625i(576i)] Horizontal 15.63 kHz, Vertical 50 Hz
[625p(576p)] Horizontal 31.25 kHz, Vertical 50 Hz
[750(720)/50p] Horizontal 37.5 kHz, Vertical 50 Hz
[1 125(1080)50i] Horizontal 28.13 kHz, Vertical 50 Hz
• HD/SYNC and V terminals are not compliant with 3 value composite SYNC
for Video signal (in-
cluding S-Video)
Horizontal 15.75 kHz / 15.63 kHz, Vertical 50 Hz / 60 Hz
for HDMI signal
525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1 125(1 080)/60p,
1 125(1 080)/50p, 1 125(1 080)/60i, 1 125(1 080)/50i
• Displayable resolution: VGA to WUXGA (non-interlace)
• Dot clock frequency: up to 162 MH
Color system
7 (NTSC, NTSC4.43, PAL, PAL-N, PAL-M, SECAM, PAL60)
Projection size
0.76 m-7.62 m(30"-300")
Screen aspect ratio
16 : 10 4 : 3
Projection scheme
Front / Rear / Mount on Ceiling / Floor (Menu setting system)
Speaker
1 (4.0 cm round-type)
Maximum usable volume
output
10 W
Contrast ratio *
2
3 500 : 1 (all white / all black) 4 000 : 1 (all white / all black)
*1: These values of light output are measured under the condition that [Lamp power] is set to [Normal],
[Image select] is set to [Dynamic] and [Lens Shift] is adjusted to the lowest level. measurement, measuring
conditions and method of notation all comply with ISO21118 international standards.
*2: The value of contrast ratio is measured under the condition that [Lamp power] is set to [Normal],
[Image select] is set to [Dynamic], [Lens Shift] is adjusted to the lowest level and [Iris] is set to [On].
Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*3: For details of video signals that can be projected using this projector, refer to “List of compatible signals” on the
user's manual.