Filter
Top Products
19 20
5.3 POWER-UP
Apply AC power to the Model 1065 by plugging the separate AC
power cable first into the rear panel of the Model 1065 and then into an
acceptable AC power outlet. The remote/normal/loopback switch
should be set to “normal”. When the local and remote Model 1065 are
poweyellow up, and passing data
normally
, the following LED condi-
tions will exist:
• TD & RD = flashing on and off
• RTS & DCD = green
• TEST = off
5.4 V.54 TEST MODES
The Model 1065 offers two V.54 test modes to evaluate the condi-
tion of the modems and the communication link. These tests can be
activated physically from the front panel, or via the RS-232 interface.
Note: V.54 test modes are available for point-to-point applications only.
5.4.1 Local Analog Loopback (LAL)
The Local Analog Loopback (LAL) test checks the operation of the
local Model 1065 Series unit, and is performed separately on each
unit. Any data sent to the local Model 1065 in this test mode will be
echoed (returned) back to the user device. For example, characters
typed on the keyboard of a terminal will appear on the terminal screen.
To perform a LAL test, follow these steps:
A. Activate LAL. This may be done in one of two ways: By mov-
ing the front panel toggle switch DOWN to "Local" or by raising pin 18
on the RS-232 interface (Note: Make sure DIP switch S2-6 is OFF,
and DIP switch S3-5 is ON). Once LAL is activated, the Model 1065s
transmit output is connected to its own receiver. The "test" LED should
be lit.
B. Verify that the data terminal equipment is operating properly and
can be used for a test. If a fault is indicated, call a technician or
replace the unit.
C. Perform a BER (bit error rate) or 511/511E test on each unit. If
the BER test equipment indicates no faults, but the data terminal indi-
cates a fault, follow the manufacturer's checkout procedures for the
data terminal. Also, check the RS-232 interface cable between the ter-
minal and the Model 1065.
5.4.2 Remote Digital Loopback (RDL)
The Remote Digital Loopback (RDL) test checks the performance
of both the local and remote Model 1065s
and
the communication link
between them. Any characters sent to the remote 1065 in this test
mode will be returned back to the originating device. For example,
characters typed on the keyboard of the local terminal will appear on
the local terminal screen
after
having been passed to the remote
Model 1065 and looped back. To perform an RDL test, follow these
steps:
A. Activate RDL. This may be done in two ways: By moving the
front panel toggle switch UP to "Remote" or by raising pin 21 on the
RS-232 interface (Note: Make sure DIP switch S3-6 is ON; and DIP
switch S2-6 is OFF).
B. Perform a BER (bit error rate) 511/511E test on the system.
C. If the BER test equipment indicates a fault, and the Local
Analog Loopback test was successful for both Model 1065 Series
units, you may have a problem with the twisted pair line between the
modems. You should then test the twisted pair line for proper connec-
tions and continuity.
5.4.3 Using the V.52 BER Test Independently
The V.52 BER test can be used independently of the V.54 loopback
tests. This requires two operators: one to initiate and monitor the test
at the local Model 1065, and one at the remote Model 1065. To use the
V.52 BER test by itself, both operators should simultaneously follow
these steps:
1. Locate the “511/511E” toggle switch on the front panel of the unit
and move it UP. This activates the V.52 BER test mode and trans-
mits a “511” test pattern to the other unit. If any errors are pres-
ent, the receiving modem's red “ERROR” LED will blink sporadi-
cally. Note: For this test to function, the “511” switch on both
Model 1065 units must be on.
2. If the test indicates no errors are present, move the V.52 toggle
switch DOWN, activating the “511/E” test with periodic errors pres-
ent. If the test is working properly, the receiving modem’s yellow
“ERROR” LED will blink
regularly
. A successful “511/E” test will
confirm that the link is in place, and that the Model 1065s’ built-in
“511” generator and detector are working properly.