Filter
Top Products
198
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5
Start adjusting
Selecting the mode for adjustment operations.
Select 1st FACTORY ADJ mode, then adjust.
Start
Select 1st FACTORY ADJ Mode
Start
1st FAC
Factory Adjustment Mode
Normal
picture
Cyclically
Front panel
2nd FAC-
TORY ADJ
mode
picture
1st FAC-
TORY ADJ
mode
picture
The 2nd FACTORY
ADJ mode is not used
in the adjustment.
INPUT1
position
Press the
switch with
thin rod.
" ON "
TV
POWER
Telop : Red
RANGE CHECK mode
(TV/SAT/DVD MENU)
Telop : White
(MUTING) (MUTING)
(MUTING)
(MUTING)
(MUTING)
(MUTING)
(MUTING)
PANEL ADJ mode
(CH RETURN)
Telop : Green
ADJUSTMENT SIZE mode
(ANT)
Telop : Magenta
ADJUSTMENT MPX mode
(P IN P ON/OFF)(SPLIT)
Telop : Blue
STD OFFSET mode
( ∞ DOWN)
Telop : White
MANUAL CONVER mode
(SET)
Telop : White
AUTO ADJ mode
( 2 LEFT)
Telop : green
TEST mode
( 3 RIGHT)
Telop : Yellow
DTV PANEL ADJ mode
(DTV)
Telop : White
SIGNAL ADJ mode
( 5 UP)
Telop : White
OFFSET CONVER mode
( ÷ DOT)
Telop : Blue , Cyclically
OTHER OFFSET mode 3
(Blue)
Not used in the
adjustment.
Telop : Blue , Cyclically
COLOR TEMP mode
(Green)
Telop : Blue
OTHER OFFSET mode
( )
1
2
2
2
3
4
5
• To enter FACTORY mode, use the
key(s) on the remote control unit or
main unit. To release FACTORY mode,
use the key(s) of the remote control unit
or the main unit, or turn the power off.
If the unit remains in FACTORY mode
without any operation for 8 minutes, it
will be automatically released.
• In FACTORY mode, data for the picture
and audio qualities are standard, and
the FLESH TONE setting is always off.
• When the unit enters FACTORY mode,
settings such as audio muting, MENU,
and SPLIT (two split-screens) are
released.
• The Convergence data which user
adjusted are within the FACTORY
mode. Clear the convergence data by
releasing the FACTORY mode after it is
further within the MANUAL CONVER
mode or OFFSET CONVER mode.
• When the unit exits FACTORY mode,
the TV/CATV mode becomes AIR
(settings of ANT and CH are those last
stored in memory).
• CONVER. OSD (cross hatch) can be
turned on and off cyclically by using the
YELLOW key only during CONVER
mode (MANUAL, AUTO, OFFSET
adjustments).
(Default: The cross hatch is on only in
CONVER. mode.)
EDIT/
LEARN
DTV
SOURCE
INFO
RECEIVER
4
¢
MENU
INPUT
AUDIO
GUIDE
8
POWER
POWER
POWER
VCR REC
VOLVOL
PROJECTION MONITOR RECEIVER
REMOTE CONTROL UNIT
Î
TV/
DTV
CBL
/SAT
DVD
/LD
VCR
1
4
7
5
8
6
9
2 3
0
ANT
DISPLAY
POWER
MUTING
MENU
MODE
SUB CH
SPLIT
SELECTSEARCH
1 2 3 4
INPUT
FAVORITE CH
TV
TV
DTV
ON/OFF
CH
ENTER
RETURN
CH
FREEZE
173¡
VOL
CH
SET/
ENTER
∞
5
2 3
DTV/SAT
DTV/DVD TOP
SCREEN
DTV/(SAT)
TV/SAT/DVD
6.4 FACTORY ADJ MODE