Filter
Top Products
RSC Series
1817
14. MAINTENANCE 16. SPECIFICATIONS
15. TROUBLESHOOTING
Cleaning the Body of the laminaor
1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Problem Cause Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
the micro switch is activated.
c. Replace the motor fuse.
The unit is not heating
up:
a. Did not raise the temperature. a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
RSC-1650C
AC100, 200, 220~240V 50/60Hz
120V 60Hz
100 W,130 W
1650mm / 65"
25 ~ 250mic / 1~10mil
5 m/min / 16.4 ft/min
Not applicable
None
DC geared
Not applicable
9 settings
2 Roller
2.25", 3"
Yes
No
Yes
15mm / 0.6"
Chain link to main moto
r
Yes
Yes
Yes
1960 x 650 x 1210 (mm)
77" x 21.5" x 47.5"
209kg / 461lbs
2190 x 900 x 1460 (mm)
86" x 35.5" x 57.5"
338kg / 745lbs
RSC-1650H
AC100, 200, 220~240V 50/60Hz
120V 60Hz
1650W,1800W
1650mm / 65"
25 ~ 250mic / 1~10mil
5 m/min / 16.4 ft/min
10 min
Hot roller
DC geared
50°C / 122°F
9 settings
2 Roller
2.25", 3"
Yes
No
Yes
15mm / 0.6"
Chain link to main motor
Yes
Yes
Yes
1960 x 650 x 1210 (mm)
77" x 21.5" x 47.5"
209kg / 461lbs
2190 x 900 x 1460 (mm)
86" x 35.5" x 57.5"
338kg / 745lbs
Description
Power supply
Power consumption
Max laminating width
Film thickness
Max laminating speed
Ready time
Heating method
Driving motor
Max. temperature control
Speed control
Transport type
Film core size
Cross cutter
Hot lamination
Cold lamination
Mounting thickness
Take up system
Reverse
Remote control
Foot pedal
Unit dimensions
(w x d x h)
Unit weight
Carton dimensions
(w x d x h)
Carton weight
RSC-1650HR
AC200, 220~240V
50/60Hz
2300W
1650mm / 65"
25 ~ 250mic / 1~10mil
5 m/min / 16.4 ft/min
15 min
Hot roller
DC geared
130°C / 266°F
9 settings
2 Roller
2.25", 3"
Yes
Yes
Yes
15mm / 0.6"
Chain link to main motor
Yes
Yes
Yes
1960 x 650 x 1210 (mm)
77" x 21.5" x 47.5"
209kg / 461lbs
2190 x 900 x 1460 (mm)
86" x 35.5" x 57.5"
338kg / 745lbs