Filter
Top Products
LS-12HBd Projection System Quick Setup Guide Page 3 020-1252-00 Rev. A (September 2013)
PRELIMINARY
PRELIMINARY
OSD Menu Tree
Input Source
Composite 1 HDMI 1
Composite 2 HDMI 2
Composite 3 HDMI 3
Component HDMI 4
HD 1 HDMI 5
HD 2 HDMI 6
SCART HDMI 7
DisplayPort HDMI 8
Aspect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Auto Cinema
Screen
Screen 1 / Screen 2
Picture
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
Input Position
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
(Zoom/Crop)
Phase
(RGB/Component/SCART signals only)
Tracking
(RGB/Component/SCART signals only)
Memory
Presets
Recall ISF Night or ISF Day
Recall/Save Custom 1 or Custom 2
Reset Custom 1 and Custom 2 to
Factory Default
3D Processing
3D Mode
(Auto, Off, Side-by-Side, Top-and-
Bottom or Frame Packing)
Reverse Eyes (On/Off)
Sleep Timer
Off, 30 Minutes, 60 Minutes, 90
Minutes, 2 Hours or 4 Hours
Information
Signal
System
Network
Field Service
Manufacturing
Calibration
Display Color -
Common Settings
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Gamma
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35, 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Color Temp Simple (5500K, 6500K, 7500K or 9300K)
Color Gamut*
Auto, REC709, SMPTE-C, EBU, Native or
PCE
PCE*
Red x, y / Green x, y / Blue x, y / White x, y
Yellow x, y / Cyan x, y / Magenta x, y
Display Color - Projector
Settings
Lamp Power (230W or 260W)
Input Image
Brightness
-50, -49 ... 0 ... 49, 50
Contrast
Color
Tint
Sharpness
Input Color
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
Offset
Chroma Delay
0, 1, 2 ... 7
(Composite inputs only)
Noise Filter 0, 1, 2 ... 63
Save ISF Night
Back / Confirm
Save ISF Day
Copy/Paste
Memory Preset
Copy Settings
Paste Settings
Aspect Ratio
Copy Settings
Paste Settings
Output Shift
Left/Right
-50, -49 ... 0 ... 49, 50
Up/Down
Width
-50, -49, 48 ... 0
Height
Screen Masking
0, 1, 2 ... 100
(Top / Bottom / Left / Right /
Test Pattern Enable)
Image Alignment
Corner Alignment
Top Left / Top Right / Bottom Left /
Bottom Right / Test Pattern Enable
Midpoint Alignment
Center / Top Middle / Left Middle /
Right Middle / Bottom Middle /
Test Pattern Enable
Adjustment Mode Both, Primary or Secondary
Splash Configure
Owner Name
ISF Calibrated
ISF Other
Splash Timer 5, 6, 7 ... 15 ... 59, 60
Splash Enable On/Off
OSD Position Hor. / Ver.
0, 1, 2 ... 100
Service
Test Video
Color Bars 1
Color Bars 2
Focus
Grey Bars
Full White
Primary / Secondary / Dual
Alignment
3D
Input Names Rename/Restore
Remote Control
Remote Code 00000 ... 08209 ... 65535 or 88999
SRC 1-7 Keys
(select a key, then choose a source to assign to it)
SRC 8-14 Keys
Display Device -
Configure
Installation -
Picture Orientation
Auto, Floor Front, Ceiling Front, Floor Rear or
Ceiling Rear
Lens
Focus
Zoom
Shift
Display Info.
(read-only)
Projector Serial Number
Lamp Hours
Lamp Hours Reset Yes / No
Diagnostics White, Red, Green, Blue, Yellow, Cyan, Magenta
Altitude Auto / High
Display 3D Settings (n/a)
Internal 3D Settings Sync Delay, Test Pattern Enable
24Hz 3D Mode 120 Hz 6:4 or 120 Hz 5:5
Network
IP Configuration
DHCP (On / Off), IP Address, Subnet Mask,
Default Gateway, Communication Test
Auto Firmware Upgrade
Auto Check for New Firmware, Auto Perform
Upgrade, Check for New Firmware
E-Mail Notification
E-Mail Address, Error Notification, Error
Notification to Runco, Periodic Service Notification,
Lamp Life Notification, Customer Information, E-
Mail Calibration Data
Remote Network Control On / Off
Color Space
Auto, REC601, REC709,
RGB-PC or RGB-Video
(Not available on Composite 1, Composite 2 or
Composite 3 inputs)
Triggers 1 / 2 / 3
Miscellaneous
Language
English, Français, Deutsch, Italiano, Español,
Svenska, (Simplified Chinese),
(Traditional Chinese), Português, (Russian),
(Japanese) or (Korean)
OSD Timer 0 (no timeout) or 5, 6, 7 ... 30 ... 60 sec.
OSD Messages On / Off
Blank Screen Color
Red/Green/Blue = 0, 1, 2, 3 ... 255
Sidebar Color
Film Mode
(SD sources only)
On / Off
CUE
(Chroma Upsampling Error)
On / Off
Sync Threshold
0, 1, 2 ... 15
(HD 1, HD 2 and Component inputs only)
HDMI
HDMI EDID Extension On / Off (per HDMI and DisplayPort input)
Audio Format
Combined / HDMI Out (Pri. Display) /
HDMI Out (Sec. Display) / HDMI Out (Audio Only)
CEC On / Off
HPD Toggle Rejection Auto
/ On / Off
Front Panel Brightness
Logo LED 0 (off), 1, 2 ... 31
Standby LED On / Off
LCD 0 (off), 1, 2, 3 or 4
Auto Power Off
Enable On / Off / No Signal
Hours 1, 2, 3, 4, ... 23, 24
Standby Mode Low Power / Fast Startup
System Reset
Note: Default settings appear in bold type. Settings marked with an asterisk (*) apply to 2D content only.