Sharp 0NY42M184304B(1) Computer Monitor User Manual


 
6
E
MOUNTING PRECAUTIONS
• Sincethemonitorisheavy,consultyourdealerbefore
installing, removing or moving the monitor.
• Wheninstalling,removingormovingthemonitor,ensure
that this is carried out by at least 2 people.
• AmountingbracketcompliantwithVESAspecications
isrequired.DonotuseanyscrewholesotherthanVESA
holes for installation.
• Whenmovingthemonitor,besuretoholditwiththe
handlesbothontherearandtheunitbottom.Donothold
theLCDpanel.Thismaycauseproductdamage,failure,or
injury.
• Installthemonitorwiththesurfaceperpendiculartoalevel
surface.Ifnecessary,themonitormaybetiltedupto20
degrees upward or downward.
• Mountingthemonitoronthewallrequiresspecialexpertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Thismonitorshouldbeusedatanambienttemperature
between32°F(0°C)and104°F(40°C).Provide
enough space around the monitor to prevent heat from
accumulating inside.
For the monitor in horizontal orientation
7-7/8 [20]
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
For the monitor in vertical orientation
(for PN-E421 only)
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
7-7/8 [20]
*
*
* This monitor can be installed close to a wall. However,
as the monitor emits heat during operation, please be
aware that this heat may discolor or alter the wall.
• Ifitisdifficulttoprovidesufficientspaceforanyreason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of32°F(0°C)to104°F(40°C),installafanortakeother
measures to keep the ambient temperature within the
required range.
• Temperatureconditionmaychangewhenusingthedisplay
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• PN-E471cannotbeusedinverticalorientation.
• Adheretothefollowingwheninstallingthemonitorinits
vertical orientation. Failing to adhere to the following may
causemalfunctions.(forPN-E421only)
-InstallthemonitorsuchthatthepowerLEDislocatedon
the downside.
-SettheMONITORontheSETUPmenutoPORTRAIT.
(See Operation guide.)
• Donotblockanyventilationopenings.Ifthetemperature
inside the monitor rises, this could lead to a malfunction.
• Aftermounting,pleasecarefullyensurethemonitoris
secure, and not able to come loose from the wall or mount.
• Donotplacethemonitoronadevicewhichgeneratesheat.
• Usethesuppliedverticalstickerwhenyouinstallthe
monitorinverticalorientation.(forPN-E421only)
Operation panel
Logo
Donotremovethefactory-afxedstickerbutafxthelogo
stickeroverit.Becarefulnottocovertheremotecontrol
sensor or buttons.
• Besuretouseawall-mountbracketdesignedor
designated for mounting the monitor.
• Thismonitorisdesignedtobeinstalledonaconcretewall
or pillar. Reinforced work might be necessary for some
materials such as plaster / thin plastic board / wood before
starting installation.
This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the
monitor. Install by the most suitable method for the material
and the structure.
• Whenattachinganoptionalpart,followthestepsdescribed
in the manual for the optional part.
• ForuseonlywithULListedWallMountBracketswith
minimumweight/load:PN-E471:102kg.(224.9lbs.),
PN-E421:88kg.(194.0lbs.).