Filter
Top Products
Adjustment Using the Menus
24
USER CONFIG menu
You can select a language, etc.
Items that cannot be adjusted depending on the input
signal are displayed in blue.
LMD-1410/2010
.
LMD-1420/2020
Submenu Setting
CONTROL You can adjust the picture.
• CONTRAST: Adjusts the picture
contrast.
• BRIGHT: Adjusts the picture
brightness.
• CHROMA: Adjusts color intensity.
The higher the setting, the greater
the intensity. The lower the setting,
the lower the intensity.
• PHASE: Adjusts color tones. The
higher the setting, the more
greenish the picture. The lower the
setting, the more purplish the
picture.
• APERTURE: Adjusts the picture
sharpness. The higher the setting,
the sharper the picture.
For details of input signals and adjustable/
setting items, see page 14.
ASPECT (LMD-
1410/2010 only)
Sets the aspect ratio of the picture to 4:3 or
16:9.
x RGB/COMP SEL xxxx
· COMP LEVEL xxxxx
· NTSC SETUP x
· GAMMA x
· FORMAT DISP xxx
· LANGUAGE xxx
· PIC DELAY MIN xxx
USER CONFIG
x RGB/COMP SEL xxxx
· COMP LEVEL xxxxx
· NTSC SETUP x
· GAMMA x
· FORMAT DISP xxx
· LANGUAGE xxx
USER CONFIG (1/2) Rr
xMARKER xxx
· CENTER MARKER xxx
· SAFETY AREA xxx
· MARKER LEVEL x
· MARKER MAT xxx
· SCAN xxxx
· PIC DELAY MIN xxx
USER CONFIG (2/2) Rr
Submenu Setting
RGB/COMP SEL When a signal input via the RGB/
COMPONENT connector is being
monitored, based on the signal being
input, select RGB or COMP.
COMP LEVEL Select the component level from among
three modes.
• SMPTE for 100/0/100/0 signal
• BETA 0 for 100/0/75/0 signal
• BETA 7.5 for 100/7.5/75/7.5 signal
NTSC SETUP Select the NTSC setup level from two
modes.
The 7.5 setup level is used mainly in
North America. The 0 setup level is used
mainly in Japan.
GAMMA Selects the appropriate gamma mode.
You can select from among 5 settings.
When “3” is selected, the setting is
roughly same as the gamma mode of the
CRT (2.2).
FORMAT DISP Select the display mode of the signal
format.
• ON: The format is always displayed.
• OFF: The display is hidden.
• AUTO: The format is displayed for
about 10 seconds when the input
of the signal begins.
LANGUAGE You can select the menu or message
language from among seven languages.
• ENGLISH: English
• DEUTSCH: German
• FRANÇAIS: French
• ITALIANO: Italian
• ESPAÑOL: Spanish
• : Japanese
• : Chinese
MARKER When the frame of the film is displayed
on the screen, select the aspect ratio
according to the film.
• When 16:9 aspect ratio is selected
with the ASPECT button
You can select from among 4:3,
15:9, 14:9, 13:9 and OFF.
• When 4:3 aspect ratio is selected
with the ASPECT button
You can select from among 16:9
and OFF.
CENTER MARKER Select ON to display the center mark of
the picture and OFF not to display.
SAFETY AREA Select the safe area size for the aspect
ratio determined by the ASPECT button.
You can select from among OFF, 80%,
85%, 88%, 90% and 93%.
MARKER LEVEL Sets the luminance to display the
MARKER and SAFETY AREA.
When the setting is low, the marker is
displayed dark.
MARKER MAT Selects whether you put mat on the
outside of the marker display.
• OFF: No mat is put.
• HALF: Gray mat is put.
• BLACK: Black mat is put.