Filter
Top Products
Cisco IOS Software Configuration for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card
How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card
10
Cisco IOS Release 12.0(8)S
–
show controllers oc12 slot/port:channel#
Verify the Cisco Remote Connection Management configuration by entering the
show controllers oc12 slot/port:channel# command, as shown in the following example:
Router# show controllers oc12 1/0:1
Controller OC12 1/0, interface Serial1/0:1 (DS3 channel 1)
cdb = 0x616BED10, base_hwidb = 0x613B5540, hwidb = 0x613B6520
ssb = 0x616C46A0, ds = 0x616C43E8
Line state is up
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI inactive, txRAI inactive
Current configurable parameter settings:
Loopback is none, Framing is c-bit
DSU mode is cisco, DSU bandwidth limit is 44210
Payload scrambling is disabled, CRC is 16
Bert pattern is disabled, Bert interval is 0
Transmitter delay is 0, Encapsulation is HDLC
Idle character is flags, Invert data is disabled
Remote fullrate has no request outstanding
Remote accept is enabled, MTU is 4470
MIB information:
Data in current interval (366 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violations
0 C-bit Coding Violations
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 0 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
No alarms detected.
Router#
–
show controllers oc12 detail
View details about an OC-12 controller by entering the show controllers oc12 detail command:
Router# show controllers oc12 detail
OC12_CH_DS31/0
The current state of the controller is up
Current configurable parameter settings:
Clock source is INTERNAL, Loopback is NONE
SECTION
LOF = 0 LOS = 0 RDOOL = 0 BIP(B1) = 0
Active Alarms: None
LINE
AIS = 0 RDI = 0 FEBE = 0 BIP(B2) = 0
Active Alarms: None
PATH 1
AIS = 0 RDI = 0 FEBE = 0 BIP(B3) = 0
LOP = 0 NEWPTR = 0 PSE = 0 NSE = 0
Active Alarms: None
S1S0 = 02, C2 = 04
PATH TRACE BUFFER : STABLE
61 6D 69 74 2D 62 66 72 00 00 00 00 00 00 00 00 anew-day........
00 00 00 00 00 00 00 00 53 65 72 69 61 6C 35 2F ........Serial5/
30 3A 31 00 00 00 31 30 31 2E 35 2E 31 2E 31 00 0:1...101.5.1.1.
00 00 00 00 00 00 30 30 30 30 30 30 30 30 0D 0A ......00000000..
PATH 2
AIS = 0 RDI = 0 FEBE = 0 BIP(B3) = 0
LOP = 0 NEWPTR = 0 PSE = 0 NSE = 0
Active Alarms: None
S1S0 = 03, C2 = FF
PATH TRACE BUFFER : STABLE
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF ................