Epson RTC-72421 B Clock User Manual


 
RTC - 72421 / 72423
Page - 3 MQ - 162 - 03
Terminal functions
Pin No.
Signal
RTC-72421 RTC-72423
Input/ou
tput
Function
D
0
-D
3
(Data bus)
11
14 14
16, 19
Bi-
direction
Connect these pines to a bi-directional data bus or CPU data bus. Use this bus
to read to and write from the internal counter and registers.
CS
1
CS
0
RD WR Mode of D
0 to
D
3
H L L H Output mode (read mode)
H L H L Input mode (write mode)
H L L L Do not use
L H or L High impedance (back-up mode)
H H H or L High impedance (RTC not selected)
A
0
-A
3
(Address bus)
4
7
5, 7, 9, 10 Input
Address input pins used for connection to CPU address, etc. Used to select the
RTC’s internal counter and registers (address selection).
When the RTC is connected to a multiplexed-bus type of CPU, these pines can
also be used in combination with the ALE described below
ALE
(Address Latch Enable)
3 4 Input
Reads in address data and
CS
0
state for internal latching.
When the ALE is high, the address data and
CS
0
state is read into the RTC.
When the (through-mode) ALE falls, the address data and
CS
0
state at that
point are held. The held address data and
CS
0
status are maintained while
the ALE is low.
ALE
Address data and CS
0
status
H
L
Read into the RTC to set address data
Held in the RTC (latched at the trailing edge of the ALE)
If the RTC is connected to a CPU that does not have an ALE pin and thus there
is no need to use this ALE pin, fix it to V
DD
.
WR
(WRite)
10 13 Input
Writes the data on D
0
to D
3
into the register of the address specified by A
0 to
A
3,
at the leading edge of
WR .
Make sure that
RD
and
WR
are never low at the same time.
RD
(ReaD)
8 11 Input
Output data to D
0
to D
3
from the register at the address specified by A
0 to
A
3,
while
RD
is low.
Make sure that
RD
and
WR
are never low at the same time.
CS
1
,
CS
0
(Chip Select)
15,2 20,2 Input
When CS
1
is high and
CS
0
is low, the RTC’s chip-select function is valid and
read and write are enabled.
When the RTC is connected to a multiplexed-bus type of CPU,
CS
0
requires
the operation of the ALE (see the description of the ALE).
Use CS
1
connected to a power voltage detection circuit. When CS
1
is high, the
RTC is enabled; when it is low, the RTC is on standby.
When CS
1
goes low, the HOLD and RESET bits in the RTC registers are
cleared to 0.
STD.P
(STanDard Pulse)
1 1 Output
This is an N-channel open drain output pin.
Depending on the setting of the C
E
register, a fixed-period interrupt signal and a
pulse signal are output.
The output from this pin cannot be inhibited by the CS
1
and
CS
0
signals.
Use a load voltage that is less than or equal to V
DD
. If not using this pin, keep it
open-circuit.
An example of STD.P connection is shown below.
At least 2.2 k
STD.P
RTC
+5 V or V
DD
If the STD.P output is not be used during standby operation, connecting the pull-
up resister to +5 V provides a reduction in current consumption. If the STD.P
output is to be used even during standby, connect the pull-up resistor to the
RTC’s V
DD
. In this case, the current consumption will be increased by the
amount of current flowing through the pull-up resistor.
V
DD
18 24
Connect this pin to power source. Supply to 5 V
±
10 % to this pin during normal
operation; at least 2 V during battery back-up operation.
GND 9 12
Connect this pin to ground.
(V
DD
) 16, 17 22,23
These pins are connected internally to V
DD
. Leave them open circuit.
N.C.
3, 6, 8,
17, 18, 21
These pins are not connected internally. Ground them.