Filter
Top Products
ENGLISH
ENGLISH
ENG
4
5
WARRANTY
Fellowes warrants all parts of the laminator to be free of defects in material and workmanship
for 2 years from the date of purchase by the original consumer. If any part is found to be defec-
tive during the warranty period, your sole and exclusive remedy will be repair or replacement,
at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases
of abuse, mishandling or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELLOWES
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ATTRIBUTABLE TO THIS PROD-
UCT. This warranty gives you specifi c legal rights. You may have other legal rights that vary from
this warranty. The duration, terms and conditions of this warranty are valid world-wide, except
where different limitations, restrictions or conditions may be required by local law. For more
details or to obtain services under this warranty, please contact us or your dealer.
1. Please insert the power cable
in the laminator and the power
supply.
HOT LAMINATION STEPS
1
2
COLD
80
mic
100
mic
HELP? TEMP
??
175
mic
125
mic
3
COLD
80
mic
100
mic
HELP? TEMP
??
175
mic
125
mic
4
2. Switch laminator on with
Power On / Off button at back
of machine.
3. Press Stand-by button at
left of front operating panel to
switch laminator on.
4. Use navigation keys to select
setting for the hot lamination
pouch thickness (3-10 mil)
you wish to laminate.
COLD
80
mic
100
mic
HELP? TEMP
??
175
mic
125
mic
5
COLD
80
mic
100
mic
125
mic
175
mic
???
EXIT
6
COLD
80 mic 100 mic 125 mic 175 mic ???
EXIT
7
5. Confi rm your selection by
pressing “Enter” button in the
middle of navigation keys.
Laminator will take a few minutes
for temperature adjustment.
6. During warm-up, a “wait”
symbol will appear in the LCD
screen until the required tem-
perature has been reached.
7. One temperature is reached,
the selected setting will fl ash in
LCD screen and acoustic bleep
signal will sound and the roller
symbols will rotate.
8. While laminator is warming
up, please prepare item you
wish to laminate. Place the item
inside the pouch and center it
against the sealed edge of the
pouch. To prevent jamming, use
a carrier when item is smaller
than the pouch.
8
9
1
0
0
9. Place pouch, sealed edge fi rst,
into laminator entry. Keep pouch
straight and use the edge guide
to center it.
10. To prevent jamming,
immediately remove laminated
item from back of machine. Let
item cool on fl at surface for
several seconds.
11. Before switching off laminator,
feed empty cleaning/carrier sheet
through machine to clean unit.
MAINTENANCE Unique Easi Access technology
MAINTENANCE - Unique Easi-Access technology
This laminator is equipped with the unique Easi-Access technology for easy maintenance. This allows the user to open the laminator for maintenance, just like a photocopier.
7. Please remember to re-secure
them to ensure safe operation.
1. To open the laminator, please press the
“Open” button as shown in the illustra-
tion and wait for the “open” symbol to
appear on the LCD screen and the ready
beep to sound.
2. Fans will turn on to cool the
machine down to safe handling
temperature inside.
3. The “Open” symbol will show
in the LCD screen will turn on and
the ready beep will sound when
machine is ready to be opened.
4. Press the buttons on both sides
of the machine to activate the Easi-
Access mechanism. (The laminator
needs to be switched on to allow the
active temperature control to work).
6. For further maintenance,
the rollers can be released by
experienced users. Press cam
levers to release the rollers.
5. Open the lid with both hands. You are
now able to clean the inside of the lamina-
tor and carefully remove any residual glue
or other items. When laminator is opened,
power to internal parts is isolated, so that
user is not in danger of electric shock.
TROUBLESHOOTING
Problem
Ready Light does not come on after extended time
Pouch did not completely adhere to item.
Jamming
Cause
Laminator is in a hot, humid area.
Laminated item may be too thick.
Pouch was not used.
Pouch was not centered or straight when fed
through Pouch/Document Entry.
Solution
Move laminator to a cool dry area.
Pass through laminator a second time.
All our laminators have been designed to operate jam-free.
In the unlikely event of a jam occurring, please press the red
release buttons on the sides of laminator, and wait for the open
light to turn on. (See image 1)
The laminator can be opened to remove incorrectly inserted items
as described under Maintenance. Please ensure that you follow
the described steps. (See image 2)
Gently pull on the jammed material to release it. (See image 3)
Make sure that no residue is left
on the rollers and use
cleaning sheet before laminating.
Always put item in a pouch.
Align sealed edge with Pouch/Document Entry. Use guide to
center
.
r
r
Need Help?
Please call our experts at
Customer Service. You’ll fi nd
the numbers for your nearest
Service Centre on the
BACK cover of this booklet.
COLD
80 mic 100 mic 125 mic 175 mic ???
EXIT
1
2
3
4
1
2
1
7
5
1
2
5
8
0
1
0
0
3
5
1
7
5
1
2
5
80
1
0
0
6
7
1
1
402103.venus.110606_3L.PS.indd Sec4:4-Sec5:5402103.venus.110606_3L.PS.indd Sec4:4-Sec5:5 11/28/06 10:03:17 AM11/28/06 10:03:17 AM