Filter
Top Products
logically grouped together and easy to access. The stand, which is included for both 24” and 44” models, is sturdy and easy to constructs.
It is then screwed to the base of the printer (the printer is shipped upside down) and then easily ipped by two people. I actually managed
to unpack, assemble, and ip the 44” model myself.
Once the printer is assembled and plugged into a power source, you can then begin the somewhat lengthy setup process. Once the printer
is powered on you will be prompted to load the printers 12 cartridges, (1)photo black (2)matte black, (3)grey, (4)light grey, (5)light cyan,
(6)magenta, (7)light Magenta, (8)yellow, (9)(NEW)chromatic red, (10)green, (11)blue, and last but not least a (12)gloss enhancer. The 24”
Z3200 ships with 69mil cartridges while the 44” model ships with the standard 130mil carts. This means that the 44” Z3200 ships with
about $400.00 of extra ink, not a trivial sum. After the cartridges are installed the printer begins to charge the lines with ink, a process
that takes several minutes. When this process was completed, the ink levels for all of the inks were around 80% full on the smaller 69mil
tanks.
After the ink carts are loaded the print heads must be installed. HP uses what they refer to a semi-permanent print heads. What does this
mean exactly? By contrast Epson uses a different print head technology, micro piezo, allowing for permanent print heads. They are not
user replaceable, but are designed to last the life of the printer, if one does malfunction its replacement is a sizeable percentage of what
a new printer would cost. Both companies will argue for the relative superiority of the technology, and both have merit. Whatever the
system, clogged print heads will lead to banding and degradation in image quality, and must be remedied. Most Epson large formt print-
ers have additionally required users to clean the heads through an ink purge, which is both time consuming and expensive. Thermal print
heads by their very nature breakdown over time, which of course necessitates the use of replaceable heads. To avoid having to replace
the print head when only a small number of nozzles are bad, the printer maps defective nozzles and uses alternate nozzles to pick up the
slack. When too many of these nozzles become inoperable you will then have to replace the head. Since very little ink is purged through
the print heads the printer does not have a require large maintance tanks.
Changing heads in the Z3200 is a quick process, taking about a minute to remove the old head and install the new one. There is one head
for every two colors, at a cost of about $70 each (list). Each head is warranteed for 1000 mils of ink but is expected to push through 2500
mils of ink before it needs replacement. Since each cart contains 130mils of ink this means you will likely go through many complete
sets of ink before any of the heads will need to be replaced. Or viewed another way, about 20 tanks could be run through a head before
it is expected to fail. That’s a fair amount of ink.
After the heads have been installed the printer nishes it’s rather lengthy initialization process during which it buzzes and hums. This is
a good time to download the printer drivers on your system. After the printer nishes initializing, the basic hardware setup is nished.
You should then load the roll of paper that ships with the printer and run the paper feed and head alignment from the printer menu. This
is a crucial step, and will help avoid banding issues and ensure maximum image quality.
INK COSTS
Aside from the 69ml starter set on the 24” printer, all ink cartridges are 130 ml. The cartridges are available as a single cartridge or in
a twin pack. HP also charges less for the gloss optimizer, which as I’ll discuss later, is a good thing.
Assuming manufacture supplied list prices let’s look at some very basic ink set costs (though most suppliers, including Spec-
traow, sell for well below list prince).
HP DESIGNJET Z3200 EPSON STYLUS PRO
7/9880
Epson 7/9900
Number of installed inks 11 colors
1 gloss enhancer (GE)
8 colors 11 colors
Ink cartridge size 130 ml 110/220 ml 150/350/700 ml
MSRP cost per cart $83 single / $62 GE
$132 double/$99 GE
($66 each)/($49.5 GE)
$70 for 110 ml
$112 for 220 ml
$89.95 for 150 ml
$159.95 for 350 ml
$279.95 for 700 ml
Total volume of ink in
printer
1560 ml 880 (110 ml carts)
1760 (220 ml carts)
3850 ml (300 ml carts)
7700 ml (700 ml carts)
Cost per replacement set $975 single
$1551 double
$560 for 110 ml
$896 for 220 ml
$1759 for 350 ml tanks
$3079 for 700 ml tanks