JVC DT-V20L3D Computer Monitor User Manual


 
8
7 Rear panel
Daily Operations / Connections (cont.)
The illustration of the monitor is of DT-V24L3D.
1 Power switch
Tur ns the power on or off.
• You need to press button ( u on page
6) to use the monitor after turning on the power
switch.
2 AC IN terminal
AC power input connector.
Connect the provided AC power cord to an AC
outlet.
• Attach the provided power cord holder to prevent
accidental disconnection of the AC power cord (
on the right).
CAUTION
Do not connect the power cord until all other
connections are completed.
3 REMOTE terminal
Ter minal for controlling the monitor by an external
control. ( “External Control” on page 16)
4 VIDEO (INPUT 1/INPUT 2) terminals (BNC)
Input (IN) and output (OUT) terminals for the
composite signals.
5 COMPO./RGB (G/Y, B/PB/B-Y, R/PR/R-Y) terminals
(BNC)
Input (IN) and output (OUT) terminals for the
analog component (color difference) or analog RGB
signals.
• Select the signal type in “COMPO./RGB SEL.”
corresponding to the type of the input signal (
page 10).
8
Note for connections
• Before making any connections, turn off all the
equipment.
• Use a cord whose plugs correctly match the
terminals on this monitor and the equipment.
• Plugs should be firmly inserted; poor connections
could cause noise.
• When unplugging a cord, be sure to grasp its plug
and pull it out.
• DO NOT connect the power cord until all connections
are complete.
• Refer also to the user manual of each piece of
equipment.
Security slot
Attach a security wire to this slot.
6 EXT.SYNC (CS) terminals (BNC)
Input (IN) and output (OUT) terminals for the
external composite sync (Cs) signals.
• To use these terminals, set “SYNC INPUT SEL.”
to “EXT.” ( “SYNC FUNCTION” on page 13)
• The terminals are for all VIDEO (INPUT 1, INPUT
2) and COMPO./RGB.
• When an external sync signal is input, external
synchronization has priority over all VIDEO 1,
VIDEO 2 and COMPO./RGB input.
7 AUDIO ASSIGN (IN 1/IN 2) terminals (pin jack)
Input terminals for the analog audio signals.
• Use this terminal for the analog audio connection
of the SDI.
• Select the video input to assign the audio signal
in “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” (
“AUDIO SETTING” on page 12).
8 AUDIO ASSIGN (MONITOR OUT) terminals
(pin jack)
Output terminals for the analog audio signal.
• The terminals output the audio signal through
AUDIO ASSIGN (IN 1 or IN 2) terminals when
you select the video input you have selected for
“AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in
“AUDIO SETTING” ( page 12).
• The signal is output from this terminal only when
the monitor is on or in “P.SAVE” (power save)
mode. ( “NO SYNC ACTION” on page 13)
• The EMBEDDED AUDIO signal...
– is decoded into an analog signal, then emitted.
– is emitted only when “SDI 1” or “SDI 2” is
selected, and when EMBEDDED AUDIO
signals come in to the E. AUDIO HD/SD SDI
(IN 1 or IN 2) terminal.
– has priority over the audio signal input to
AUDIO ASSIGN (IN 1 or IN 2) terminals when
“SDI-1” or “SDI-2” is selected for “AUDIO1
ASSIGN.” or “AUDIO2 ASSIGN.” and the
EMBEDDED AUDIO signal is input to E.AUDIO
HD/SD SDI (IN 1 or IN 2) terminal.
9 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD/SD SDI signals.
• The terminals accept also EMBEDDED AUDIO
signals including up to 12 audio channels with a
sampling frequency of 48 kHz.
p E. AUDIO HD/SD SDI (SWITCHED OUT) terminal
(BNC)
Output terminal for the HD/SD SDI signals.
• The SDI signals of the current input (SDI 1 or SDI
2) are re-clocked, then emitted.
• When an input other than SDI 1 and SDI 2 is
selected, the SDI signal of the input selected last
time is emitted from this terminal.
• The signals are emitted from this terminal only
when the monitor is on or in “P.SAVE” (power
save) mode.
q DVI-D (HDCP) terminal
Input terminal for the DVI-D signal compatible with
HDCP.
• When the picture is not displayed correctly,
change the setting of “DVI INPUT SEL.”
( page 10).
Using the audio level meter
You can check the conditions of the current
EMBEDDED AUDIO signals in the audio level meter.
(
On the Information Display
on page 7)
Make the setting for the level meter in
“LEVEL METER
SETTING” (
“AUDIO SETTING” on page 12).
Attaching the power cord holder
The provided power cord holder prevents accidental
disconnection of the AC power cord from the AC IN
terminal.
The power cord holder consists of two parts, a
case and a cover.
1
2
3
CAUTION
Use only the provided screws.
Make sure the plug will not be pulled out after the
cover is attached to the case.
To detach the cover
AC IN terminal
Case
Cover
2
1
DT-V24_20L3D_EN.indd 8DT-V24_20L3D_EN.indd 8 08.5.27 5:14:58 PM08.5.27 5:14:58 PM