Filter
Top Products
Filename [HRS8700EU2.fm]
Masterpage:Left
36
EN
Page 36 July 20, 2000 4:31 pm
TIMER RECORDING (cont.)
Automatic Satellite
Programme
Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the recorder’s AV2 (L-2) IN/DECODER connector and
programme the timer on the satellite receiver. The
recorder starts or stops recording by the signals input
from the satellite receiver. After recording, the recorder’s
power shuts off automatically.
A
Select the L-2 SELECT mode.
Set “L-2 SELECT” to “A/V” or “SAT” (
੬
pg. 51).
● When you select “SAT”, refer to “IMPORTANT” on page 60.
B
Set the tape speed.
Press
SP/LP/EP
(
p
).
● It is not possible to select EP mode if “COLOUR SYSTEM” is
set to “MESECAM”
. (
੬
pg. 67
)
C
Engage the Automatic Satellite Programme
Recording mode.
Press and hold
SAT#
for about 2 seconds. The SAT
#
indicator lights up and the recorder turns off
automatically.
NOTES:
● To disengage the Automatic Satellite Programme Recording mode, press
SAT
#. The SAT# indicator goes off.
● If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.
● In step
3
, if the SAT
# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic
Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer
Programming” (
੬
pg. 32) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.
● The SAT
# indicator blinks while Automatic Satellite Programme Recording is in progress.
● For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
● Pressing the recorder’s
1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and
disengages the Automatic Satellite Programme Recording mode.
● If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible
to set different tape speeds for each programme.
● Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may
record slightly longer than the actual length of the programme.
● If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start
Automatic Satellite Programme Recording even though the SAT
# indicator blinks. When the satellite receiver shuts off once and is
turned back on again, the recorder starts recording.
● You can also record a programme from your cable system in the same way if the system has a timer.
● The B.E.S.T. system (
੬
pg. 29) does not work while Automatic Satellite Programme Recording is in progress.
● Just Clock (
੬
pg. 76) does not work when the Automatic Satellite Programme Recording mode is engaged.
● When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite
Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”
(
੬
pg. 65).
SAT# indicator
ATTENTION
● Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the recorder will start
recording when the satellite receiver’s power is turned on.
● If you have connected another appliance other than a
satellite receiver to the AV2 (L-2) IN/DECODER connector,
be sure not to engage the Automatic Satellite Programme
Recording mode; otherwise, the recorder will start
recording when the connected appliance’s power is turned
on.
● Automatic Satellite Programme Recording and
timer-recording cannot be done at the same time.
Before performing the following steps:
● Make sure the satellite receiver is connected to the recorder’s
AV2 (L-2) IN/DECODER connector. (
੬
pg. 60, 61)
● Programme the timer on the satellite receiver.
● Insert a cassette with the safety tab in place.
HRS8700EU2.fm Page 36 Thursday, July 20, 2000 4:31 PM