Panasonic PT-AE3000U Projector Accessories User Manual


 
ENGLISH - 37
Settings
POSITION menu
You can move the projected image horizontally for fine
adjustment.
You can move the projected image vertically for fine
adjustment.
If you have interference patterns of the projected image,
which is sometimes referred to as moire or noise, you
can minimize it by pressing I H to adjust the clock
frequency. (Available with signals from COMPUTER IN
only)
If you require further adjustment for the same reason as
the DOT CLOCK adjustment, you can fine adjust the
timing of the clock. Press I H to adjust. (Available with
signals from COMPUTER IN/COMPONENT IN only)
You can switch the aspect ratio manually when needed.
J Aspect ratio depend on signals
Press I H to cycle through the aspect ratio
options. The cycle pattern depends on the
connected signals.
H-POSITION
V-POSITION
DOT CLOCK
NOTE:
If the projecting signal’s dot clock frequency is higher
than 150 MHz, the adjustment may not make a
difference.
DOT CLOCK needs to be adjusted before adjusting the
CLOCK PHASE.
Remote control Control panel
See “Navigating through the MENU” on page 29.
See “Main menu and sub-menu” on page 30.
Move
right
Move left
Move up
Move
down
CLOCK PHASE
NOTE:
If the projecting signal’s dot clock frequency is higher
than 150 MHz, the adjustment may not make a
difference.
Available signals from COMPONENT IN:
1 125 (1 080)/60i, 1 125 (1 080)/50i, 1 125 (1 080)/60p,
1 125 (1 080)/50p, 1 125 (1 080)/24p, 750 (720)/60p,
750 (720)/50p.
ASPECT
VIDEO/
S-VIDEO
4:3 \ 16:9 \ s16:9 \ JUST \ ZOOM
\ AUTO
NTSC, NTSC 4.43, PAL-M, PAL60
signals
4:3 \ 16:9 \ s16:9 \ 14:9 \ ZOOM1
\ ZOOM2 \ JUST
PAL, PAL-N, SECAM signals
COMPUTER
(RGB)
4:3 \ 16:9
VGA, SVGA, XGA, SXGA, MXGA signals
Not switchable with WIDE480/600/720/
768/768-2/800/900 signals
HDMI
4:3 \ 16:9 \ s16:9 \ H - FIT \ V - FIT
\ ZOOM
1 125 (1 080)/50i, 1 125 (1 080)/60i,
1 125 (1 080)/50p, 1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p and
750 (720)/60p signals
4:3 \ 16:9 \ s16:9 \ JUST \ ZOOM
525i (480i), 625i (576i), 525p (480p) and
625p (576p) signals
COMPONENT
(YPBPR)
4:3 \ 16:9 \ s16:9 \ 14:9 \ ZOOM1
\ ZOOM2 \ JUST
625i (576i), 625p (576p) signals
AUTO \ 4:3 \ 16:9 \ s16:9 \ JUST
\ ZOOM
525i (480i), 525p (480p) signals
4:3 \ 16:9 \ s16:9 \ H - FIT \
V - FIT \ ZOOM
1 125 (1 080)/50i, 1 125 (1 080)/60i,
1 125 (1 080)/50p, 1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p,
750 (720)/60p signals