Filter
Top Products
8 61225101L1-5B
Figure 5. Express 6530 Menu Tree
Software Optioning
The menu tree in Figure 5 illustrates the path to every
provisioning, performance monitoring, and test access
point in the Express 6530 menu system.
1. Unit Information
Main Menu
2. Provisioning
2. LT
1. NT
1. PN127
2. V.54
2. Disable
1. Enable
1. -15. Threshold in dB
0. Disabled
2. Inverted
1. Normal
2. DTE Driven
1. Permanent Off
2. DTE Driven
1. Permanent Off
1. -999. Time out
0. Disabled
2. Test Driven
1. Permanent Off
1. -100. Delay in Seconds
0. Disabled
2. From DTE, ETC (circuit 113)
1. From DCE, TC (circuit 114)
2. Inverted
3. Auto
1. Normal
1. -127. Threshold in dB
0. Disabled
0. -225. Delay in ms
5. Performance History
(15-minute and 24-hour Registers)
6. Terminal Mode
* Enter a new value for N from 3 to 36, where the aggregate rate (Kbps) = (Nx64) + 8
** From 00h to 1Fh for static condition of NFAS spare bits (0, 0, 0, Sa4, Sa5, Sa6, Sa7, Sa8)
3. Status
4. Test
2. [Local Unit] G.703
3. [Remote Unit] SHDSL
1. [Local Unit] SHDSL
2. G.703 Loopback Type
3. G.703 Services Loopback Type Ñ Service 1.-31.
4. Nx64k Loopback Type
1. SHDSL Loopback Type
2. Transparent
1. Dual Sided
3. Nontransparent
2. Permanent On
1. Permanent Off
3. RTS Driven (V.24)
4. RTS Driven (C107 Emulation)
2. Permanent On
1. Permanent Off
3. Sync Mode
2. Permanent On
1. Permanent Off
3. Sync Mode
2. SNR Margin
Alarm Threshold (dB)
1. Aggregate Rate (Kbps)*
3. Loop Attenuation
Alarm Threshold (dB)
2. Nx64k ETC
1. Internal
3. G.703 RX Clock
2. SHDSL Options
1. Unit Options
3. G.703 Options
5. Test Options
4. Nx64k Options
NTU
LTU
1. Unit Mode
2. Cross-Connect Map
3. LT Mode Clock Source
4. Circuit ID
5. Date and Time
8. Local Management
9. Change Password
7. Download Firmware
6. Reset Factory Defaults
2. SHDSL Remote Loopback
1. SHDSL Local Loopback
3. SHDSL BERT
4. G.703 Local Loopback
5. G.703 BERT
6. G.703 Services
8. Nx64k Remote Loopback
Send In-band Pattern
9. Nx64k BERT
7. Nx64k Local Loopback
1. Inactivity Alarm Delay (Secs)
3. TX Clock Polarity
2. TX Clock Source
5. CTS (Circuit 106)
6. RTS to CTS Delay (ms)
4. RTS (Circuit 105)
1. Permanent On
2. DTE Driven
1. Permanent On
2. DTE Driven
8. DTR (Circuit 108/2)
9. RLSD (Circuit 109)
7. DSR (Circuit 107)
2. G.704 CRC-4 Multiframing
1. IDSN-PRA V3
3. G.704 Idle Pattern Ñ from 00h to FFh
5. Network Spare Bits Pattern**
4. Network Spare Bits Insertion
6. Customer Spare Bits Insertion
7. Customer Spare Bits Pattern**
9. Customer E-Bit Generation
8. Customer RAI Generation
2. [Local Unit] G.703 Port
1. [Local Unit] SHDSL Port
3. [Local Unit] G.703 Services
5. [Remote Unit] SHDSL Port
4. [Local Unit] Nx64k Port
2. Customer Transparent
1. Dual Sided
3. Customer Nontransparent
5. Network Nontransparent
4. Network Transparent
1. In-Band Loopback Protocol
2. G.703 Services Pattern Detection
3. Nx64k In-Band Pattern Detection
2. In-band Loopback Options
1. Loopback Types
3. Loopback Time Out (Minutes)
5. Pushbuttons (All)
4. BERT Test Pattern Polarity
6. SHDSL Port Select Pushbutton
7. V.35 RL (Circuit 140)
9. V.35 TI (Circuit 142)
8. V.35 LL (Circuit 141)
Service 1. -31.
NOTE:
4. Outage Auto-Retrain
5. Line Probing