Filter
Top Products
Table of Contents
i-1
5975039 BARCOVISION 508 100698
i
TABLE OF CONTENTS
TABLE OF CONTENTS .......................................... I-1
SAFETY INSTRUCTIONS ...................................... 1-1
On safety....................................................................................1-1
On installation .............................................................................1-2
On servicing ...............................................................................1-2
On cleaning.................................................................................1-2
On repacking ..............................................................................1-2
On illumination .............................................................................1-2
LOCATION AND FUNCTIONS OF
CONTROL .............................................................. 2-1
Rear Panel Terminology..............................................................2-1
Front Panel Terminology .............................................................2-1
Control panel terminology...........................................................2-2
a. The local keypad ....................................................................2-2
b. RCU control panel terminology ...............................................2-2
CONNECTIONS ..................................................... 3-1
Switching on/off.........................................................................3-1
Signal input connection to the projector : ..................................3-1
Power (mains) cord connection ................................................3-1
Connecting a Composite Video source. ....................................3-2
Connecting a S-Video to port 2..................................................3-2
Connecting a RGB Analog source with composite sync..........3-3
Connecting a Component source. .............................................3-4
Connecting a RF signal to the projector (optional) ....................3-4
Connecting an external audio signal (optional) .........................3-5
Peripheral equipment ..................................................................3-5
Connecting a RCVDS 05 switcher to the projector...................3-5
Connecting a VS05 switcher to the projector...........................3-5
Connecting an IR Remote Receiver to the projector.................3-5
CONTROLLING ..................................................... 4-1
Battery installation in the RCU. ...................................................4-1
How to use the RCU...................................................................4-2
Projector address.......................................................................4-2
How to display a projector address? ........................................4-2
How to program an address into the RCU? ..............................4-3
Input selection.............................................................................4-3
Picture controls ..........................................................................4-4
The Pause key............................................................................4-4
Sound control with the RCU (optional) ......................................4-5
START UP OF THE ADJUSTMENT
MODE ..................................................................... 5-1
Adjustment mode........................................................................5-1
RANDOM ACCESS ADJUSTMENT
MODE ..................................................................... 6-1
Starting up the random access adjustment mode. ....................6-1
Overview 'random Access Adjustment' mode..........................6-1
Selecting Setup Pattern ..............................................................6-2
Internal Cross Hatch Pattern ......................................................6-2
Random access adjustment mode selection menu. ..................6-2
Picture Tuning .............................................................................6-2
Color Balance .............................................................................6-3
Gamma ........................................................................................6-3
Blue stretch ................................................................................6-3
Decoding.....................................................................................6-3
Color Select ................................................................................6-4
Geometry Adjustments...............................................................6-4
Horizontal Phase Adjustment .....................................................6-5
Raster Shift Adjustment .............................................................6-5
Left-Right (east-west) Adjustments..........................................6-7
Top-Bottom (north-south) Adjustments .....................................6-8
Horizontal Size Adjustment ........................................................6-9
Vertical Linearity Adjustment .....................................................6-9
Horizontal Size Adjustment ......................................................6-10
Blanking Adjustments ...............................................................6-10
Convergence Adjustment ........................................................6-12
SERVICE MODE .................................................... 7-1
Starting up the Service mode.....................................................7-1
Overview flowchart 'Service' mode..........................................7-1
Projector Set-up .........................................................................7-2
Identification................................................................................7-2
Total Run Time ............................................................................ 7-3
Change password .....................................................................7-3
Change Projector Address ........................................................7-3
Change baudrate........................................................................7-4
Power up mode ..........................................................................7-4
Memory management ................................................................. 7-4
Copy a block ...............................................................................7-5
Deletion of blocks .......................................................................7-5
Deleting block by block ...............................................................7-5
Deletion of all blocks...................................................................7-6
All settings to midposition...........................................................7-6
Undo all settings to midpos ........................................................7-6
R & B convergence mid..............................................................7-7
Undo R & B convergence mid ....................................................7-7
Green convergence mid ............................................................7-7
Undo green convergence mid....................................................7-7
Common Settings........................................................................ 7-8
G2 Adjustment ............................................................................7-8
CRT run in cycle .........................................................................7-8
I2C Diagnostics ...........................................................................7-9
OPTIONS ............................................................... 8-1
IR Receiver 800 ..........................................................................8-1
Hardwired RCU. .........................................................................8-1
RCVDS 05 Source Selector .......................................................8-1
VS05 Switcher ...........................................................................8-1
Adapter and communication cables ..........................................8-1
Ceiling mount CM50 .................................................................... 8-1
Tuner kit ......................................................................................8-2
APP. A : TUNER MODE........................................ A-1
Tuner mode................................................................................ A-1
How to activate the tuner mode ? ............................................A-1
Tuner setup ...............................................................................A-2
Broadcasting System ................................................................A-2
Auto search...............................................................................A-3
Manual search ...........................................................................A-3
Organise channel list................................................................. A-4
Bilingual ......................................................................................A-4
Teletext ...................................................................................... A-5