Filter
Top Products
15
Installation and Configuration Note for the Catalyst 4500 Series Supervisor Engine V
78-15590-02
Installing and Removing the Supervisor Engine
Step 6 Align the edges of the supervisor engine carrier with the slot guides on the sides of the switch chassis,
as shown in Figure 2.
Figure 2 Installing the Supervisor Engine in the Chassis
Step 7
Pivot the two module ejector levers out and away from the faceplate.
Step 8 Carefully slide the supervisor engine into the slot until the notches on both ejector levers engage the
chassis sides.
Step 9 Using the thumb and forefinger of each hand, simultaneously pivot in both ejector levers to fully seat the
supervisor engine in the backplane connector.
Caution Always use the ejector levers when installing or removing a supervisor engine. A supervisor engine that
is partially seated in the backplane will not function correctly.
Step 10 Use a screwdriver to tighten the captive installation screws on each end of the supervisor engine
faceplate.
To check the status of the module, perform these steps:
Step 1 Ensure that the LED labeled Status is green (module operational).
Step 2 When the switch is online, enter the show module command. Verify that the system acknowledges the
new module and that the module’s status is good.
Step 3 If the module is not operational, reseat it. If the module is still not operational, contact your customer
service representative.
79001
W
S
-
X
4
4
4
8
-
G
B
-
R
J
4
5
S
T
A
T
U
S
1
2
11
1
0
9
8
7
6
5
4
3
2
1
1
4
1
3
1
6
1
5
2
8
27
2
6
2
5
2
4
2
3
2
2
2
1
2
0
1
9
1
8
1
7
3
0
2
9
3
2
3
1
4
4
4
3
4
2
4
1
4
0
3
9
3
8
3
7
36
3
5
3
4
33
4
6
4
5
4
8
4
7
1
0
/1
0
0
B
A
S
E
-T
X
E
TH
E
R
N
E
T
M
U
L
T
I-S
P
E
E
D
G
IG
A
B
IT
E
T
H
E
R
N
E
T
S
W
IT
C
H
I
N
G
M
O
D
U
L
E
W
S
-
X
4
4
4
8
-
G
B
-
R
J
4
5
S
T
A
T
U
S
1
2
11
1
0
9
8
7
6
5
4
3
2
1
1
4
1
3
1
6
15
2
8
27
2
6
2
5
2
4
2
3
2
2
2
1
2
0
1
9
1
8
1
7
3
0
2
9
3
2
31
4
4
4
3
42
4
1
4
0
3
9
3
8
3
7
36
3
5
3
4
3
3
4
6
4
5
4
8
4
7
1
0
/10
0
B
A
S
E
-T
X
E
T
H
E
R
N
E
T
M
U
L
T
I-
SP
EE
D
G
I
G
A
B
I
T
E
T
H
E
R
N
E
T
S
W
IT
C
H
I
N
G
M
O
D
U
L
E
1
STATUS
WS-X4412-2GB-TX
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
7
1
STATUS
WS-X4412-2GB-TX
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
7
1
STATUS
WS-X4412-2GB-TX
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
7
U
P
LIN
K
U
P
L
IN
K
C
O
N
S
O
L
E
1
0
/1
0
0
B
A
S
E
-
T
X
S
T
A
T
U
S
UPL
IN
K 1
LINK
AC
TIV
E
LINK
AC
TIV
E
UPLIN
K 2
C
O
NS
O
LE 10
/10
0 M
G
T
EJ
E
CT
FLAS
H
UT
ILI
ZA
TION
S
T
A
T
U
S
S
U
P
E
R
V
I
S
O
R
I
II E
N
G
IN
E
W
S
-
X
4
0
1
4
1
%
1
0
0
%
R
ES
E
T