Eaton Electrical APR48 Power Supply User Manual


 
Data Power Solutions Quick Start Guide
Copyright © 2006-2009 Eaton Corporation. All Rights Reserved.
10640205 February 2009
13
Wartung
Bei Data Power Solutions-Anlagen liegen gefährliche Spannungen an. Sie dürfen das Gerät ohne
entsprechende technische Ausbildung weder auseinanderbauen noch warten. Das Warten des Geräts darf nur
durch Wartungspersonal der Telecommunications Solutions Division von Eaton oder durch von Eaton
zugelassene Wartungstechniker erfolgen.
Für andere Wartungsarbeiten als das Austauschen der externen Batterien oder des Gleichrichters der
Stromversorgungsanlage isolieren Sie das Gerät zunächst wie folgt:
Ziehen Sie die Netzstecker aus der Netzsteckdose.
Trennen Sie die externen Batterien, indem Sie die Batterieschutzschalter ausschalten.
Manutenzione
In Data Power Solutions sono presenti tensioni pericolose. Non cercare di disassemblare o riparare l'unità, se
non si è qualificati per farlo. Gli interventi di manutenzione sull'unità sono consentiti esclusivamente al
personale di assistenza della divisione Telecommunications Solutions della Eaton Corporation o a eventuali
tecnici da loro autorizzati.
Se il sistema di alimentazione richiede una manutenzione diversa dalla sostituzione della batteria esterna o del
raddrizzatore, innanzitutto isolate la prima unità, come indicato di seguito:
Scollegare i cavi di alimentazione C.A. dalle prese C.A.
Scollegare le batterie esterne, spegnendo gli interruttori della batteria.
Reparaciones
Las Soluciones de Energía para Datos contienen voltajes peligrosos. No trate de desarmar ni de reparar la
unidad si no está capacitado para hacerlo. Solo el personal de reparaciones de la División de Soluciones para
Telecomunicación de la corporación Eaton o sus agentes de reparación autorizados podrán reparar la unidad.
Si el sistema de energía necesita ser reparado, excepto si se trata de reemplazar la batería externa o el
rectificador, primero aísle la unidad, como se indica a continuación:
Desconecte los cables CA de los enchufes CA.
Desconecte las baterías externas, apagando los interruptores de circuito de la batería.
EMC Compliance
APS dc power systems may be used in close proximity to other electronic equipment provided installation is
carried out according to instructions in this manual. However, proper installation and compliance with EMC
standards does not guarantee that the APS dc power system will not respond to electromagnetic disturbances,
or will not cause interference to other equipment in a particular installation.
APS3 and APS6 power systems comply with part 15 of the FCC (Federal Communications Commission) rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications to APS dc power systems not approved by Eaton Corporation could void FCC
authority to operate that equipment.
APS3 and APS6 power systems have been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.