Filter
Top Products
Controls and Features
1 Remote Control’s signal transmitter
(☞ page 17)
2 OPERATE button
When the projector is in the standby mode, pressing this
button for one second or more will turn on the projector and
light up the OPERATE indicator. Press it one second or
more again and the projector will turn off, cool down and
finally enter the standby mode.(☞ page 24)
* The OPERATE button will not work for approximately 1
minute from when the light-source lamp is turned on. Use
the button after approximately 1 minute.
3 SCREEN button
Each time you press this button, the selection alternates
between wide screen size (16:9) and standard screen size
(4:3). (☞ page 30)
4 DIGITAL ZOOM ª / · buttons
This digital zoom function can magnify the image up to four
times on the screen. (☞ page 27)
* There will however be some inevitable loss of image qual-
ity when images are enlarged.
5 FREEZE button
This button allows the image to be retained in the projector
memory and stills the picture on the screen. Press the but-
ton once to freeze the picture and again to de-freeze.
(☞ page 28)
6 QUICK ALIGN. (quick alignment) button
Use this button to automatically adjust the projected im-
age’s (i)horizontal and vertical position, (ii) Width and dis-
play area, etc. During alignment, the message “QUICK
ALIGN.” appears on the screen and disappears when align-
ment is complete. (☞ page 30)
* The ‘Quick Alignment’ function only works when the sig-
nal is input from either the PC 1 or PC 2 terminal. It does
not work when the signal is input from the VIDEO IN ter-
minal or the Y/C input terminal.
7 EXIT button
Press this button to display the previous hierarchical menu
(For example, from sub-menu to main menu). When the
main menu is displayed, pressing this button will cause the
menu to disappear. (☞ page 34)
8 ENTER button
Press this button to show the next hierarchical menu (For
example, from main menu to sub menu). It is also used
when “ENTER” is displayed against the item on the menu
screen or to select the “Reset” menu. (☞ page 34)
9 HIDE button
Use this button to turn off the image on the screen and
audio sound temporarily. Pressing it again causes the im-
age and audio sound to resume. (☞ page 28)
p CURSOR ( ᮡ/ ᮢ / ᮤ / ᮣ ) buttons
These buttons are used in the menu mode to select an
item, adjust the value etc. (☞ page 34)
q VIDEO button
Use this button to select a device such as a video con-
nected to the VIDEO IN terminal (VIDEO or Y/C Input ter-
minal) of the projector. (☞ page 24)
w PC button
Use this button to select a device connected to the PC 1,
PC 2 or PC 3 terminal. (☞ page 25)
e H-KEYSTONE button
Use this button to remove the horizontal trapezoidal distor-
tion of the image projected on the screen. (☞ page 29)
r V-KEYSTONE button
Use this button to remove the vertical trapezoidal distortion
of the image projected on the screen. (☞ page 29)
t VOLUME ª / · button
Use these buttons to adjust the sound volume.
(☞ page 28)
y FOCUS button*
Not Active
u MENU button
Use this button to enter or exit the menu mode. When the
main menu is displayed, press this button and it will disap-
pear. (☞ page 34)
i PRESET button
This PRESET button only works as a reset button for the
[VOLUME], [V-KEYSTONE] and [H-KEYSTONE] adjust-
ments done on the control panel and the [VOLUME],
[DIGITAL ZOOM] and [SCREEN „] adjustments done on
the remote control. (☞ page 27, 29)
When adjusting the volume, keystone or digital zoom (when
the setting is displayed on the screen) the adjusted value is
reset to that which was set when the projector was shipped
from the factory. This button does not work for the menu
(submenu) items. (☞ page 34)
12