Filter
Top Products
Message table (continued)
Indicators
The POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases.
POWER
indicator
Lights orange
Flashes green
Lights green
Flashes orange
LAMP
indicator
Turns off
Turns off
Turns off
Turns off
TEMP
indicator
Turns off
Turns off
Turns off
Turns off
Message Processing
Standby status
Warming up
Operation status ,1
Cool down
Wait some time (approx. 20 min.) before
Lights red Lights red Turns off The lamp does not light. *2 turning the power on again, Ifthe
indicator still lights, the lamp may have
failed and. Replace with a new lamp.
Lights red Flashes red Turns off A lamp has not been inserted Firmly insert the lamp as far as possible
or the lamp cover is missing, and screw the lamp cover in place,
Lights red Turns off Flashes red The coolingfan is notoperating. Contact your dealer,
Flashes red Flashes red Turns off The totallamptime has Contact your dealer,
exceededthe replacementtime.
When the LAMP e!' TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your
dealer or service company.
*1: When the cooling fan is stopped and the interior becomes overheated, the power will tam off automatically to allow cooling (the indicator will turn
off). In such cases, turn offthe projector power, allow the set to cool and then tam the projector power on again. The lamp will then ligN. If the lamp
does not light, contact your dealer or service company.
*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP
iMicator will flash red. In such cases, turn offthe MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.
When you think something wrong
Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then
contact your dealer.
Symptom Possible cause Remedy Page
The power is not ,The main power switch is not turned on. ,Tom on the main power switch. P.13
turned on. ,The power cord is disconnected. ,Plugthe powercordinto anAC poweroutlet. P.9
No video oraudio. ,The input is not correctly set. ,Use the projector or remote control to set. P.8.10,
13,19
•No signal input. ,Connect correctly. P.9.31
Video is present but ,The projector is notcorrectly connected. ,Connect correctly. P.9.31
no audio. ,The volume is seet to minimum. ,Press VOLUME + on the remote control or display P.10.18
the menu screen and adjust the volume.
•Mute is turned on. ,Press the MUTE button. P.8.10
•Audio is switched to Video when P in P is on. ,DisplaystheVolumebarandswitchestheAudioinput. P.10
Audio is present but ,The projector is notcorrectly connected. ,Connect correctly. P.9.31
no video. ,The brightness adjustment knob is rotated ,Select BRIGHT with the MENU button and then P.17
fully clockwise, press the (@) ) key.
•The lens cap is still on. ,Remove the lens cap. P.13
Colorsarepale and Color density and color matching are not Adjust the video. P.18
colormatching ispoor. correctly adjusted.
Images are dark. ,Brightnessandcontrastarenotcorrectlyadjusted. ,Adjust the video. P.18
•The lampisnearingthe endof its servicelife. ,Replace with a new lamp. P.32
Video is blurred. Focus or H PHASE is out of adjustment. Adjust the focus or H PHASE. P.13.18
The LAMP indicator Lamp failure. Wait approximately 20 min. and then turn the P.33
lights red. power on again.
The TEMP indicator Internal overheating. ,Make surethe ventilationopeningsare notblocked. P.31.32
lights red. ,Clean the air filter.
•Lowertheambienttemperatureto 35degreesCorless.
A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.
/
33